A force 8.0 newtonsis is applied to an object with a mass of 250g.what will be the acceleration of the object due to the force?

Answers

Answer 1

Answer:

32m/s^2

Explanation:

force=8.0N

Mass=250g

Converting from gram to kilogram :

250g=(250g) * (1kg)/(1000g)

The grams cancel out, to give

=0.25kg

acceleration =?

Force= mass of object * it's accelaration

Where,

Force = F

mass = m

acceleration =a

8.0N = 0.25kg * a

Therefore, a = 8.0N/0.25kg

a= 32m/s^2.

Force is responsible for causing an object with mass to change its velocity (which includes to begin moving from a state of rest), i.e., to accelerate.

Therefore, the acceleration of the object is 32m/s^2.

Answer 2

Final answer:

The acceleration of the object due to a force of 8.0 N is 32 m/s².

Explanation:

To find the acceleration of an object due to a force, you can use the formula F = ma, where F is the force applied, m is the mass of the object, and a is the acceleration. In this case, the force applied is 8.0 N and the mass is 250 g. However, it is important to convert the mass to kilograms before using the formula. So, the mass becomes 0.250 kg. Plugging these values into the formula, we get:

F = ma
8.0 N = 0.250 kg × a

To solve for a, divide both sides of the equation by 0.250 kg:

a = 8.0 N ÷ 0.250 kg

a = 32 m/s²

Therefore, the acceleration of the object due to the force of 8.0 N is 32 m/s².


Related Questions

Liquids usually have higher volume coefficients of expansion than solids do.
true or false

Answers

Answer: true

Explanation:

The answer is true! Hope this helps!! :)

Phys 131 HW#2
Q#1 Red laser beam enters hits glass/ water interface with an angle of 30° find the
angle of the refracted beam in the water. (20)

Answers

Angle of refraction: [tex]34.6^{\circ}[/tex]

Explanation:

Refraction is a phenomenon that occurs when light crosses the interface between two mediums.

When this occurs, the ray of light bends, according to Snell's law:

[tex]n_1 sin \theta_1 = n_2 sin \theta_2[/tex]

where

[tex]n_1,n_2[/tex] are the index of refraction of the two mediums, respectively

[tex]\theta_1[/tex] is the angle of incidence (the angle between the incident ray and the normal to the surface)

[tex]\theta_2[/tex] is the angle of refraction (the angle between the refracted ray and the normal to the surface)

In this problem, we have:

[tex]n_1 = 1.513[/tex] (index of refraction of glass for red light)

[tex]n_2 = 1.331[/tex] (index of refraction of water for red light)

[tex]\theta_1=30^{\circ}[/tex] (angle of incidence)

Therefore, the angle of refraction is:

[tex]\theta_2 = sin^{-1}(\frac{n_1}{n_2}sin \theta_1)=sin^{-1}(\frac{1.513}{1.331}sin 30^{\circ})=34.6^{\circ}[/tex]

The angle of the refracted beam in the water is approximately 22.04 degrees.

 To find the angle of the refracted beam in the water, we use Snell's Law, which relates the angle of incidence, the angle of refraction, and the indices of refraction of the two media. Snell's Law is given by:

[tex]\[ n_1 \sin(\theta_1) = n_2 \sin(\theta_2) \][/tex]

where:

[tex]- \( n_1 \) i[/tex]s the index of refraction of the first medium (air in this case),

[tex]- \( \theta_1 \)[/tex] is the angle of incidence in the first medium,

[tex]- \( n_2 \[/tex]) is the index of refraction of the second medium (water in this case),

[tex]- \( \theta_2 \)[/tex]is the angle of refraction in the second medium.

Given that the angle of incidence [tex]\( \theta_1 \)[/tex] is 30 degrees, and assuming the index of refraction for air [tex]\( n_1 \)[/tex]is approximately 1 (since it is very close to 1), and the index of refraction for water \( n_2 \) is about 1.33, we can rearrange Snell's Law to solve for[tex]\( \theta_2 \):[/tex]

[tex]\[ \sin(\theta_2) = \frac{n_1}{n_2} \sin(\theta_1[/tex]

[tex]\[ \sin(\theta_2) = \frac{1}{2.66} \][/tex]

[tex]\[ \sin(\theta_2) \approx 0.3758 \][/tex]

Now, we take the inverse sine (arcsine) to find the angle [tex]\( \theta_2 \):[/tex]

[tex]\[ \theta_2 = \arcsin(0.3758) \][/tex]

[tex]\[ \theta_2 \approx 22.04^\circ \][/tex]

Therefore, the angle of the refracted beam in the water is approximately 22.04 degrees."

Force that opposes motion between two surfaces

Answers

Answer:

Friction force

Explanation:

Friction force is a force that opposes a motion from moving but friction may seem a bad thing but it is very useful for writting and for other things. please give me a like and thank me.

Final answer:

The force that opposes motion between two surfaces is known as friction. It depends on the types of materials and surfaces in contact. There are four types of friction: Static, Sliding, Rolling, and Fluid, and each one has practical applications in our daily lives.

Explanation:

The force that opposes motion between two surfaces is known as friction in physics. Friction is everywhere in our daily lives. It's the force that allows us to walk, ride a bike, or even hold objects in our hands. The amount of friction between two surfaces is dependent on the type of materials in contact and how rough the surfaces are. For example, ice has less friction than gravel.

There are four types of friction: Static, Sliding, Rolling, and Fluid. The friction that opposes motion between two stationary objects (when you try to slide a heavy box, for instance) is known as static friction. When the objects are set in motion, the friction is known as sliding friction. A moving object over the surface like a wheel over the road experiences rolling friction. Fluid friction refers to the resistance between layers within a viscous fluid or when the fluid is moving over a surface. Each type of friction has important practical applications and implications in our day-to-day life.

Learn more about Friction here:

https://brainly.com/question/35899777

#SPJ6

Because of __, all objects are attracted to each other

Answers

According to Newton’s third law, Because of GRAVITY, all object are attracted to each other!

Answer:

GRAVITY

Explanation:

Newtons third law, "Gravity" attracts all objects to each other.

The maximum force that a grocery bag can withstand without ripping is 250 n. Suppose that the bag is filled with 20 kg of groceries and lifted with an acceleration of 5.0 m/s2. Do the groceries stay in the bag?

Answers

Final answer:

The force exerted by the filled grocery bag when it is lifted with an acceleration of 5.0 m/s² would be 294 N. As this is higher than the maximum force the bag can withstand (250 N), the bag would rip, and the groceries would not stay within it.

Explanation:

The maximum force that a grocery bag can withstand without ripping is 250 N. Suppose that the bag is filled with 20 kg of groceries and lifted with an acceleration of 5.0 m/s²; we need to verify if the groceries stay in the bag. The force exerted by the bag, according to Newton's second law (F=ma), will be the mass of the groceries (m) times the gravitational acceleration (g) plus the additional acceleration due to lifting (a). Here, g=9.8 m/s², and the bag is lifted with a=5 m/s².

 

The force exerted by the filled grocery bag will be F=(m*(g+a))= 20 kg*(9.8 m/s²+5.0 m/s²)= 294 N.

Since 294 N is greater than the maximum force the bag can withstand (250 N), the bag will rip, and the groceries will not stay in the bag if the bag is lifted with an acceleration of 5.0 m/s².

Learn more about Applied Force here:

https://brainly.com/question/28946328

#SPJ2

A car travels 300 km in 6 hours. What is the average speed of the car (in km/hr)

Answers

To find the average speed of the car, divide 300 km into 6 hours. It should equal 50 km per hour.

The average speed of the car that travels 300 km in 6 hours is 5 km/hours.

HOW TO CALCULATE AVERAGE SPEED:

The average speed of a moving object can be calculated by dividing the distance moved by the time taken as follows:

Average speed (km/hr) = distance (km) ÷ time (hr)

According to this question, a car travels at 300 km in 6 hours. The average speed can be calculated as follows:

Average speed = 300km ÷ 6hrs

Average speed = 5km/hr.

Therefore, the average speed of the car that travels 300 km in 6 hours is 5 km/hours.

Learn more at: https://brainly.com/question/17289046?referrer=searchResults

A student pushes on a crate with the force of 100 Newtons directed to the right. What force does the crate exert on the student? Note: It has to be done with the Newton's 2nd Law of Motion.

Answers

Answer: The Force exerted on the student by crate will be 100 N.

Explanation: As per the given Question student is trying to push the crate in right direction with the force of 100N.

And we know that, Newton's third law states that every action has equal and opposite reaction.

So from the Newton's 3rd law of motion it is very clear the student must be experiencing the same amount of force which he is applying.

Compare the numbers of protons and electrons in a positive ion with the numbers of protons and electrons in a negative ion.

Answers

Answer:

In a positive ion, the number of protons is larger than the number of electrons.

In a negative ion, the number of protons is smaller than the number of electrons.

Explanation:

Each proton carries a positive charge of one unit.

Each elec in tron carries a negative charge of one unit.

In an atom, there are as many protons as electrons. Hence, they are neutral.

However, in a positive ion, there are less negative charge than positive charge. Hence the net charge is positive. That also means that there are fewer negatively-charged electrons than positively-charged protons.

Similarly, in a negative ion, there are more negative charge than positive charge. Hence the net charge is negative. That also means that there are more negatively-charged electrons than positively-charged protons.

What is a horizontal segment meaning on a position vs. time graph?

Answers

The velocity of the object is zero (the object is at rest)

Explanation:

A position vs time graph represents the motion of an object; in particular:

The position of the object x(t) is represented on the y-axisThe time t is represented on the x-axis

For a position-time graph, the slope of the graph is given by

[tex]m=\frac{\Delta x}{\Delta t}[/tex]

where

[tex]\Delta x[/tex] is the change in position

[tex]\Delta t[/tex] is the change in time

However, we see that this is equivalent to the definition of velocity:

[tex]v=\frac{\Delta x}{\Delta t}[/tex]

Therefore, the slope of  a position-time graph is equivalent to the velocity of the object.

And so, a horizontal segment on a position vs time graph means that the object has zero velocity (because the slope is zero).

Learn more about velocity:

brainly.com/question/5248528

#LearnwithBrainly

When you push a child on a swing, you are doing work on the child because _____.


the child is moving in the direction you are pushing

you are allowing the child to continue swinging

you are pushing against the force of gravity

the child is moving at a constant velocity

Answers

.....................The answer is D

Answer:the child is moving at a constant velocity

The equivalent resistance of a complex circuit is usually determined by

Answers

Answer:

simplifying the circuit into groups of series and parallel circuits.

Explanation:

The density of an object is defined as its mass divided by its volume. Suppose the mass and volume of a rock are measured to be 8
g and 2.8325 cm^3.

What is the correct number of significant figures for the rock's density?
Express your answer using one significant figure.

Answers

Answer: 3g/cm3

Explanation:

Mass = 8g

Volume = 2.8325 cm^3.

Density = Mass / volume

Density = 8/2.8325 = 3g/cm3

How many electrons in a hydrogen atom?

Answers

Answer:

Explanation:

Hydrogen is the first element on the periodic table. That tells you there is 1 electron.

Why does every element except hydrogen need at least one neutron and its nucleus?

Answers

Answer:

It needs attractive force from the strong nuclear interaction to counter the electrostatic repulsion between the protons.

Explanation:

It has to counter

Final answer:

Other elements apart from hydrogen need at least one neutron in their nuclei to stabilize the electrostatic repulsion between protons. Neutrons add to the atomic mass and contribute to the stability of atoms. The varying number of neutrons leads to different isotopes of an element which is an essential factor in the structure and behavior of elements.

Explanation:

Neutrons play a key role in the stability of an atom. While hydrogen, with an atomic number of 1, can exist without neutrons in its nucleus, other elements require neutrons to offset the electrostatic repulsion between protons, which are all positively charged. The presence of neutrons in the nucleus contributes to the atomic mass and helps to maintain the stability of atoms as it keeps the protons from repelling each other and breaking the nucleus apart.

Isotopes are versions of the same element with a different number of neutrons, leading to variations in their atomic mass. For example, helium has an atomic number of 2 and an atomic mass of 4 because it has two neutrons in addition to two protons. As we move across the periodic table, the ratio of neutrons to protons in the nucleus generally increases, aiding in the stability of heavier elements.

The atomic mass of an element is not simply its atomic number (the number of protons) but the combination of the number of protons and neutrons. Protons and neutrons have nearly identical masses, and each contributes significantly to the mass of an atom. This concept is integral when considering the structure and behavior of elements and in understanding the composition of the human body, which is largely made up of elements like oxygen, carbon, and hydrogen.

How to find a total resistance of the circuit

Answers

Answer:

To find the total resistance of the circuit:

They are 2 ways to get that ( you can use both methods for 1 exercise)

1- If resistances are series, just add together .

Rt = R1 + R2

2 If are parallel, do the same thing but the inverse of each resistance .

Rt =1/R1 + 1/R2

Final answer:

The total resistance in a circuit with series and parallel components can be calculated by summing the resistances in series and using the reciprocal rule for resistors in parallel, before combining the two results.

Explanation:

To calculate the total resistance in a circuit, one must know the configuration of the resistors, whether they are in series, parallel, or a combination of both. The student's question suggests they are dealing with a combination of series and parallel circuits, requiring different approaches for each section.

For resistors in series, the total resistance, Rtot, is the sum of all individual resistances. So, if we have resistors R1, R2, and R3 in series, the Rtot would simply be R1 + R2 + R3.

In a parallel configuration, the total resistance, Rp, is found using the formula 1/Rp = 1/R2 + 1/R3. After calculating Rp, if this parallel combination is in series with another resistor R1, then the overall total resistance is Rtot = R1 + Rp. To get the value of Rp, one would calculate the reciprocal of the sum of the reciprocals of the individual resistances in parallel, and then take the reciprocal of that result.

By following these rules, and using the correct units and values given for the resistors, students can accurately determine the total resistance of various circuit configurations.

write out a correct version of:
"the fuel in a nuclear power station is hydrogen gas"​

Answers

"the fuel in a nuclear power station is Uranium 235"​

Explanation:

Nuclear fuel is one of the sources of energy. Nuclear fission is the method used to create nuclear energy. Nuclear fission is defined as the breaking down of the helium atoms to hydrogen which produces large amounts of energy. There is one method of preparing nuclear energy which is nuclear fusion. It is the fusion of four hydrogen atoms to form one helium atom. It happens only in the Sun. It produces a larger amount of energy than fissionThe fuel used in a nuclear power station is Uranium 235 and plutonium 239 and these are the radioactive metals.

6. When you lift a heavy box and place it on top of
put the box on the table, it remains stationary. We h
object, you either add to or take away from its energ
the energy of the box? Was it potential or kinetic er

Answers

Answer:

6 bub

Explanation:

Lifting a heavy box and placing it on a table increases its potential energy due to the work done against gravity. The box remains stationary with this added potential energy. If the box were to fall, this potential energy would be converted into kinetic energy as it accelerates towards the ground.

When you lift an object such as a heavy box and place it on a table, if the box remains stationary, it means that you have changed its energy state. Specifically, you have increased its potential energy. Potential energy is the energy stored in an object as a result of its position or height. For example, in Physics, lifting a 20 kg box of books through a vertical distance of 2m would involve an energy expenditure of approximately 400 J, signifying that the box gained 400 J of potential energy. This energy transfer occurs because of the work done against gravity: applying a force to lift the object off the ground increases its potential energy. Once the object is released, if it falls, the stored potential energy is converted into kinetic energy as it accelerates towards the ground due to the force of gravity.

It is important to note that while lifting the object, if it is done slowly so that the box's speed does not change significantly, the kinetic energy of the object remains constant (nearly zero if lifted slowly enough), although its potential energy increases. This concept is exemplified when an object is lifted using a device powered by chemical energy, such as a gasoline engine; the chemical energy is converted into gravitational energy, which is then stored in the object as potential energy. When it comes to work and energy, the work done on an object adds to its total energy. If that work is done to lift an object against the force of gravity, it is stored as potential energy.


What do most stars originally form as?
A. protostars
B. photon stars
C. neutron stars
D. binary stars or multiple stars

Answers

Answer:

Protostars

Explanation:

Most stars originally form from protostars.

11. Name given to the elements located in group 2.
a. Noble gases
c. Alkaline earth metals
b. Halogens
d. Alkali metals

Answers

Answer:

c. Alkaline earth metals

Explanation:

Your answer is Alkaline Earth Metals

The coil springs on a car's suspension have a value of k = 64000 N/m. When the
car strikes a bump the springs briefly compress by 5.0 cm (.05 m). How much
energy is momentarily stored in each spring?

Answers

80 joule is momentarily stored in each spring

Solution:

Given that,

The coil springs on a car's suspension have a value of k = 64000 N/m

When the  car strikes a bump the springs briefly compress by 5.0 cm (.05 m)

By compressing the spring, we apply a force over a distance

As a result we have done work on the spring

Doing work means that we have transferred energy to spring in form of elastic potential

Therefore,

k = 64000 N/m

x = 0.05m

The elastic potential energy is given as:

[tex]PE = \frac{1}{2}kx^2[/tex]

Where, "k" is the spring constant and "x" is the displacement

[tex]PE = \frac{1}{2} \times 64000 \times 0.05^2\\\\PE = 32000 \times 0.0025\\\\PE = 80[/tex]

Thus 80 joule is momentarily stored in each spring

The energy momentarily stored in each spring is[tex]\(\frac{1}{2} \times 64000 \times (0.05)^2 = 80\) joules.[/tex]

To find the energy stored in a spring when it is compressed, one can use the formula for elastic potential energy, which is given by:

[tex]\[ U = \frac{1}{2} k x^2 \][/tex]

where U is the elastic potential energy, k is the spring constant, and x is the compression or extension of the spring from its equilibrium position.

Given that the spring constant k is 64000 N/m and the compression x is 5.0 cm (which is 0.05 m when converted to meters), we can substitute these values into the formula:

[tex]\[ U = \frac{1}{2} \times 64000 \times (0.05)^2 \][/tex]

[tex]\[ U = \frac{1}{2} \times 64000 \times 0.0025 \][/tex]

[tex]\[ U = 32000 \times 0.0025 \][/tex]

[tex]\[ U = 80 \][/tex]

Therefore, the energy momentarily stored in each spring is 80 joules.

14. Looking ahead: Give an example of how the Law of Conservation of Energy applies to eating your favorite meal. Give at least 2 energy transformations.(5 pts)

Answers

Answer:

The law of conservation of energy applies to eating your favorite food in that the energy contained in the food is being converted to energy usable for the body system after the final digestion(Glucose or simple sugar, amino acid, etc)

Examples of transformation of energy include

(1) Transformation from Chemical energy in battery to light energy in bulb

(2) Transformation of Electrical energy to thermal/Heat energy in electric stove.

Explanation:

The law of conservation of energy states that energy can neither be created or distroy. It can only by converted from one form to another.

Final answer:

The Law of Conservation of Energy states that energy cannot be created or destroyed, but can be transformed. When eating your favorite meal, the chemical energy in the food is transformed into mechanical energy (chewing) and thermal energy (digestion).

Explanation:

The Law of Conservation of Energy states that energy cannot be created or destroyed, but it can be transformed from one form to another. This applies to eating your favorite meal because the food you eat contains chemical energy, which is then converted into other forms of energy as your body digests and metabolizes the food. Two examples of energy transformations in the process of eating your favorite meal are:

1. Chemical to Mechanical Energy: When you chew your food, the muscles in your jaw contract and expand, converting the chemical energy in the food into mechanical energy.

2. Chemical to Thermal Energy: As your body breaks down the food, chemical reactions take place, releasing heat energy in the form of thermal energy.

A wave of amplitude 20mm has intensity Ix. Another wave of the same frequency but of amplitude 5mm has an intensity Iy.
What is Ix/Iy?
A.2
B.4
C.16
D.256

Answers

Answer:

(C) 16

Explanation:

Given:

The amplitude of first wave (s₁) = 20 mm

The amplitude of second wave (s₂) = 5 mm

Intensity of first wave = Iₓ

Intensity of second wave = [tex]I_y[/tex]

The intensity associated with a wave depends on the amplitude of the wave.

The intensity (I) is directly proportional to the square of the amplitude (s) of the wave and is expressed as:

[tex]I=ks^2\\Where\ k\to constant\ of\ proportionality[/tex]

Now, the intensities of the two waves are given as:

[tex]I_x=ks_1^2=k(20)^2\\\\I_y=ks_2^2=k(5)^2[/tex]

Dividing both the intensities, we get:

[tex]\frac{I_x}{I_y}=\frac{k(20)^2}{k(5)^2}\\\\\frac{I_x}{I_y}=\frac{400}{25}\\\\\frac{I_x}{I_y}=16[/tex]

Therefore, the option (C) is correct.

The intensity of a wave is directly proportional to the square of its amplitude. The ratio of Ix to Iy is 16. Therefore, the correct answer is C. 16.

The intensity (I) of a wave is related to its amplitude (A) by the following equation:

I = (1/2) * ρ * v * ω^2 * A^2

Where:

I is the intensity.

ρ is the density of the medium through which the wave is traveling.

v is the velocity of the wave in the medium.

ω is the angular frequency (equal to 2π times the frequency of the wave).

A is the amplitude of the wave.

Since both waves have the same frequency and are traveling through the same medium, ρ and v will be the same for both waves. Therefore, we can simplify the intensity ratio (Ix/Iy) using the amplitude ratio (Ax/Ay) as follows:

Ix/Iy = (1/2) * (ρ * v * ω^2 * Ax^2) / (1/2) * (ρ * v * ω^2 * Ay^2)

The ρ, v, and ω^2 factors cancel out:

Ix/Iy = (Ax^2) / (Ay^2)

Now, we can plug in the values given:

Ix/Iy = (20mm)^2 / (5mm)^2

Ix/Iy = (400mm^2) / (25mm^2)

Ix/Iy = 16

So, Ix/Iy = 16.

Therefore, the correct answer is C. 16.

Learn more about Wave intensity here:

https://brainly.com/question/32730973

#SPJ3


Sound waves are introduced to a medium by a vibration. For example, a vibrating guitar string forces surrounding air molecules to be compressed and expanded. This creates a pressure disturbance consisting of an alternating bands of compressions and rarefactions. The vibration travels from particle to particle through the medium, transporting energy as it moves.
The amount of energy which is transported past a given area of the medium per unit of time is known as the ________ of the sound wave and is reported as
power
area
.

A) frequency
B) intensity
C) pitch
D) wavelength

Answers

the answer is A. frequency

The correct answer is B) intensity, which denotes the amount of sound wave energy transported per unit time through a unit area.

The amount of energy which is transported past a given area of the medium per unit of time is known as the intensity of the sound wave. Therefore, the correct answer to the question is B) intensity. Intensity is reported in terms of power per unit area (Watts per square meter, W/m2). It is a critical concept in acoustics that describes how sound waves carry energy through a medium, be it a fluid such as air or a solid.

In the process of sound propagation, a vibrating object such as a guitar string, transfers energy to the surrounding medium creating regions of compressions and rarefactions. These regions of varying pressure travel as longitudinal waves, which means they move along the same axis as the direction of the wave. The sound waves carry energy and this energy transfer per unit time across a unit area is what is quantified by the intensity.

1. What is the power when a voltage of 120 V drives a 2-A current through a device?
P=?
V=
Pa
P=

Answers

Yo sup??

To solve this question we must know that

P=VI

V=120 V

I=2 A

Therefore by using the above formula we get

P=120*2

=240 J

Hope this helps.

Answer: 240watt

Explanation:

V = 120 V

I = 2A

P = IV = 2 x 120

P = 240watt

Which of the following describes the time over which a periodic wave repeats?
A. frequency
B. wavelength
C. amplitude
D. period

Answers

Answer:

C

Explanation:

i dont know im just guessing im way too young for this stuff

the time over which a periodic wave repeats describes as a time period.

What is a periodic wave?

A wave with a recurrent pattern that controls its wavelength and frequency is called a periodic wave. The time it takes for a waveform to complete one cycle is referred to as a period, and the frequency is the number of cycles per second of time. It has amplitude, period, and frequency characteristics.

Frequency:

Frequency is the number of occurrences of a repeating event per unit of time.

Wavelength:

A waveform signal that is carried in space or down a wire has a wavelength, which is the separation between two identical places (adjacent crests) in consecutive cycles.

Amplitude (A):

The maximum displacement of a wave on either side of its mean position is called Amplitude.

Time Period (T):

The time taken to complete one vibration is called the Time period.

therefore, period describes the time over which a periodic wave repeats.

Learn more about periodic waves here:

https://brainly.com/question/14588679

#SPJ6

hi:) anyone able to explain what’s human reaction time in physics ? Thank you in advanced :)

Answers

Answer:

A reaction time is something that measures the amount of time for you to respond to a stimulus. For an example the average human reaction time for a visual stimulus is 0.25 seconds, 0.17 seconds for a audio stimulus and 0.15 seconds for a touch stimulus.

Explanation:

Stimulus - A thing or event that evokes a specific functional reaction in an organ or tissue

A 4.0kg block is sliding with a constant velocity of 3.0m/s on a frictionless table that is 0.5m high. If all of the block’s energy were kinetic energy, how fast would the block be moving?

Answers

Answer:

Velocity = 4.33[m/s]

Explanation:

The total energy or mechanical energy is the sum of the potential energy plus the kinetic energy, as it is known the velocity and the height, we can determine the total energy.

[tex]E_{M}=E_{p} + E_{k} \\E_{p} = potential energy [J]\\E_{k} = kinetic energy [J]\\where:\\E_{p} =m*g*h\\E_{p} = 4*9.81*0.5=19.62[J]\\E_{k}=\frac{1}{2} *m*v^{2} \\E_{k}=\frac{1}{2} *4*(3)^{2} \\E_{k}=18[J]\\Therefore\\E_{M} =18+19.62\\E_{M}=37.62[J][/tex]

All this energy will become kinetic energy and we can find the velocity.

[tex]37.62=\frac{1}{2} *m*v^{2} \\v=\sqrt{\frac{37.62*2}{4} } \\v=4.33[m/s][/tex]

(d) A beam of white light shines onto a sheet of white paper. An identical beam of light shines onto a mirror. The light is scattered from the paper and reflected from the mirror.

Answers

Final answer:

The question relates to how white light spreads out or reflects on a white paper and a mirror, governed by the law of reflection in Physics. Diffused light allows a sheet of paper to be visible from multiple angles, while a mirror reflects light at specific angles based on its smooth surface.

Explanation:

The question pertains to the law of reflection in Physics, looking specifically at how light behaves when shining on different surfaces. When a beam of white light shines onto a sheet of white paper, the light is scattered, or diffused, due to the roughness of the paper's surface. This scattering allows the paper to be seen from various angles. In contrast, when the identical beam shines onto a mirror, the light is reflected because of the mirror's smooth surface.

The reflection adheres to the law of reflection, which states that the angle of reflection equals the angle of incidence (θr = θi). White light on yellow paper and yellow light on white paper will result in color changes due to the colors being absorbed or reflected, whereas red and green lights on white paper may combine to produce a different color perception depending on the superposition of the lights.

a student uses a simple machine to help lift a load.when 40N of input force is applied to the machine it is able to lift 160N .what is the mechanical advantage of the machine

Answers

Final answer:

The mechanical advantage of the machine is 4, indicating it multiplies the input force by a factor of four.

Explanation:

The student is asking about the concept of mechanical advantage (MA), which is a measure of the force amplification achieved by using a tool, mechanical device, or machine system. The mechanical advantage is calculated as the ratio of the output force to the input force. In this case, a machine lifts a load with an output force of 160N when an input force of 40N is applied. Thus, the mechanical advantage of the machine is calculated by dividing the output force by the input force.

MA = Output Force / Input Force = 160N / 40N = 4.

So, the mechanical advantage of the machine is 4, which means the machine multiplies the input force by four times.

What is an example of a non contact force

Answers

Answer: Gravitational force

Explanation:

A non contact force can be described as a force applied to an object by another body that is not in direct contact with it.

For example, an object thrown upwards will return back due to the force of gravity acting on it. So, it means Gravitational force is acting on the body without necessarily being in contact with that body.

Other Questions
Who can bring suit to stop action by a federal agency? a. Only the Justice Department b. Only the company or individual affected by the agency action c. Another federal agency d. Citizen and environmental groups Which process is most likely used to transport glucose into a muscle cell? By referring to the attorney by his title but calling other employees by their first names, the law firm is transmitting their organizational culture through _______.A.material symbolsB.artifactsC.ritualsD.languageE.legends If Felicia lives 1 1/5 miles from the school and 9/10mile from the doctor field how much closer would she live if she lived 7/10 like from the doctor field A 36.2 g object has a heat capacity of 12.5 J/ oC. How much energy (in J) is required to raise the temperature by 5.73 oC? Hoover Corp., a wholesaler of music equipment, issued $20,000,000 of 20-year, 6% callable bonds on March 1, 20Y2, at their face amount, with interest payable on March 1 and September 1. The fiscal year of the company is the calendar year. The nurse administers an oral preparation of liquid Tylenol 650 mg is ordered. Afterward, the patient indicates he had been receiving Tylenol 650 mg in pill form. Which statement is accurate in regards to the five rights? A) The nurse failed to deliver the correct dose. B) The nurse failed to administer the light medication. C) The nurse did not violate the five rights. What its 3 to the power of 4 equal Two workers push on a wooden crate. One worker push with a force of 543 N and the other with a force of 333 N. The mass of the wooden crate is 206 kg. What is the acceleration of the crate? A year ago, you invested $2,500 in a savings account that pays an annual interest rate of 2.5%. What is your approximate annual real rate of return if the rate of inflation was 3.4% over the year? 2. Explain what might be happening to the cells in the tissues of your hand or foot whenyou feel the sensation of them "being asleep." Please help me!Simplify the expression (x+3)24(x+3). A waitress sold 11 ribeye steak dinners and 12 grilled salmon dinners, totaling $560.63 on a particular day. Another day she sold 16 ribeye steak dinners and 6 grilled salmon dinners, totaling $584.46. How much did each type of dinner cost? The enhancement of contrast at the edge of an object is the result of:a. lateral inhibition in the retina.b. the diffraction of light from the edge's surface.c. fatigue of the rods and cones.d. the color of the object. Type the correct answer in the box. Spell all words correctly.What work does a food scientist do?A food scientist conducts research on thecontent of food.ResetNext According to Tom Duncan's basic categories of contact or touch points, which of the following best describes interactions that occur with a company or brand during the process of buying or using the product or service?A. Intrinsic touch pointsB. Company created touch pointsC. Unexpected touch pointsD. Customer-initiated touch pointsE. Distributive touch points What do the headlines show about reaction to theboycott?It was supportive.It was sometimes violent.It all took place in courtrooms. The check is written and signed by A. PayeeB. Drawee C. Payer D. Drawer A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5 /km. The line resistance is negligible. The line voltage at the plant is 480/08 V (rms), and the plant consumes 120 kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using.a. Complex power approachb. Circuit analysis approach. Fina wants to use substitution to solve the system of equations. explain what she needs to do before using substitution. then solve the system of equations:2x - y = 3-1.5x + 3y = -18