Answer:
[tex]9.56\cdot 10^{-7} C[/tex]
Explanation:
A parallel-plate capacitors consist of two parallel plates charged with opposite charge.
Since the distance between the plates (1 cm) is very small compared to the side of the plates (19 cm), we can consider these two plates as two infinite sheets of charge.
The electric field between two infinite sheets with opposite charge is:
[tex]E=\frac{\sigma}{\epsilon_0}[/tex]
where
[tex]\sigma=\frac{Q}{A}[/tex] is the surface charge density, where
Q is the charge on the plate
A is the area of the plate
[tex]\epsilon_0 = 8.85\cdot 10^{-12}F/m[/tex] is the vacuum permittivity
In this problem:
- The side of one plate is
L = 19 cm = 0.19 m
So the area is
[tex]A=L^2=(0.19)^2=0.036m^2[/tex]
Here we want to find the maximum charge that can be stored on the plates such that the value of the electric field does not overcome:
[tex]E=3\cdot 10^6 N/C[/tex]
Substituting this value into the previous formula and re-arranging it for Q, we find the charge:
[tex]E=\frac{Q}{A\epsilon_0}\\Q=EA\epsilon_0 = (3\cdot 10^6)(0.036)(8.85\cdot 10^{-12})=9.56\cdot 10^{-7} C[/tex]
Cylinder A has a mass of 2kg and cylinder B has a mass of 10kg. Determinethe velocity of A after it has displaced 2m from its original starting position. Neglect the mass of the cable and pulleys and assume that both cylinders start at res
The velocity of A is 5.16m/s²
Explanation:
Given-
mass of cylinder A, mₐ = 2kg
mass of cylinder B, mb = 10kg
Distance, s = 2m
Velocity of A, v = ?
Let acceleration due to gravity, g = 10m/s²
We know,
[tex]a = \frac{mb * g - ma * g}{ma + mb} \\\\a = \frac{10 * 10 - 2 * 10}{ 2 + 10} \\\\a = \frac{80}{12} \\\\a = 6.67m/s^2[/tex]
We know,
[tex]v = \sqrt{2as}[/tex]
[tex]v = \sqrt{2 X 6.67 X 2} \\\\v = \sqrt{26.68} \\\\v = 5.16m/s^2[/tex]
Therefore, the velocity of A is 5.16m/s²
Describe what changes you would expect to see in a plot of absorbance versus temperature in an optical melting experiment on a self-complementary duplex.
Answer:
#Check explanation below for a detailed description.
Explanation:
A plot of absorbance vs temperature is used to determine [tex]T_m[/tex] of a duplex DNA.
-The duplex DNA denatures.
-The denaturation creates two single strands which enhances Ultraviolet absorption ( increased temperatures increases absorption rates).
-Higher concentrations of [tex]Sodium \ Chloride[/tex] hampers stability of the DNA.
An airplane is flying horizontally with a speed of 103 km/hr (278 m/s) when it drops a payload. The payload hits the ground 30 s later. (Neglect air drag and the curvature of the Earth. Take g = 10 m/s².)
At what altitude H is the airplane flying?
Answer:
H = 4500 m
Explanation:
Once dropped, the payload moves along a trajectory, that can be decomposed along two directions independent each other.Just by convenience, we choose these directions to be coincident with the horizontal (-x) and vertical (y) axes.As both movements are independent each other due to both are perpendicular, in the vertical direction, the initial speed is 0.So, in order to find the vertical displacement at any point in time, we can use the following kinematic equation, where a=-g., and H = -Δy.[tex]H = \frac{1}{2}*g*t^{2} = \frac{1}{2} * 10 m/s2*(30s)^{2} = 4500 m[/tex]
The airpane was flying at a 4500 m altitude.Three individual point charges are placed at the following positions in the x-y plane:Q3= 5.0 nC at (x, y) = (0,0);Q2= -3.0 nC at (x, y) = (4 cm, 0); and Q1= ?nC at (x, y) = (2 cm,0);What isthe magnitude, and sign, ofcharge Q1such that the net force exerted on charge Q3, exerted bycharges Q1and Q2, is zero?
Answer:
Explanation:
net force exerted on charge Q₃, exerted by charges Q₁and Q₂, will be zero
if net electric field due to charges Q₁ and Q₂ at origin is zero .
electric field due to Q₂
= 9 X 10⁹ X 3 x10⁹ / .04²
electric field due to Q₁
= 9 X 10⁹ X Q₁ / .02²
For equilibrium
9 X 10⁹ X Q₁ / .02² = 9 X 10⁹ X 3 x10⁻⁹ / .04²
Q₁ = 3 X10⁻⁹ x .02² / .04²
= 3 / 4 x 10⁻⁹
.75 x 10⁻⁹ C
A 62.0 kg skier is moving at 6.90 m/s on a frictionless, horizontal, snow-covered plateau when she encounters a rough patch 4.50 m long. The coefficient of kinetic friction between this patch and her skis is 0.300. After crossing the rough patch and returning to friction-free snow, she skis down an icy, frictionless hill 2.50 m high.
How fast is the skier moving when she gets to the bottom ofthe hill?
Final answer:
The skier is moving at 11.1 m/s when she gets to the bottom of the hill. This solution is derived using the principles of energy conservation and work done by friction.
Explanation:
A 62.0 kg skier is moving at 6.90 m/s on a frictionless, horizontal, snow-covered plateau when she encounters a rough patch 4.50 m long. The coefficient of kinetic friction between this patch and her skis is 0.300. After crossing the rough patch and returning to friction-free snow, she skis down an icy, frictionless hill 2.50 m high. To determine how fast the skier is moving when she gets to the bottom of the hill, we analyze the problem using principles of energy conservation and work done by friction.
We start with the equation that equates the final kinetic and potential energies to the initial energies along with the work done by friction. This equation is 0.5 mv² + 0 = 0.5 mu² + μmgl + mgh, where v is the final velocity, μ is the coefficient of friction, g is the acceleration due to gravity (9.8 m/s²), l is the length of the rough patch, and h is the height of the hill.
Plugging in the given values,
we have: 0.5 v² = 0.5 x 6.9 x 6.9 + 0.3 x 9.8 x 4.5 + 9.8 x 2.50. S
implifying, we get v² = 123.07, which leads to v = 11.1 m/s.
Thus, the skier's speed at the bottom of the hill is 11.1 m/s.
What determines whether the equilibrium temperature of a mixture of two amounts of water will be closer to the initially cooler or warmer water?
Final answer:
The equilibrium temperature of a mixture of two amounts of water will be closer to the initially cooler water due to the specific heat capacity of water.
Explanation:
The equilibrium temperature of a mixture of two amounts of water will be closer to the initially cooler water.
When different temperatures of water are mixed, heat is transferred between them until they reach a common equilibrium temperature. The amount of heat transferred is determined by the specific heat capacity of water, which is greater than most common substances. As a result, water undergoes a smaller temperature change for a given heat transfer. Therefore, the equilibrium temperature will be closer to the initially cooler water.
A small sphere is at rest at the top of a frictionless semicylindrical surface. The sphere is given a slight nudge to the right so that it slides along the surface. Let R = 1.45 ft and let the angle at which the sphere separates from the cylinder be θs = 34°. The sphere was placed in motion at the very top of the cylinder. Determine the sphare;s initial speed.
Answer:
vi = 4.77 ft/s
Explanation:
Given:
- The radius of the surface R = 1.45 ft
- The Angle at which the the sphere leaves
- Initial velocity vi
- Final velocity vf
Find:
Determine the sphere's initial speed.
Solution:
- Newton's second law of motion in centripetal direction is given as:
m*g*cos(θ) - N = m*v^2 / R
Where, m: mass of sphere
g: Gravitational Acceleration
θ: Angle with the vertical
N: Normal contact force.
- The sphere leaves surface at θ = 34°. The Normal contact is N = 0. Then we have:
m*g*cos(θ) - 0 = m*vf^2 / R
g*cos(θ) = vf^2 / R
vf^2 = R*g*cos(θ)
vf^2 = 1.45*32.2*cos(34)
vf^2 = 38.708 ft/s
- Using conservation of energy for initial release point and point where sphere leaves cylinder:
ΔK.E = ΔP.E
0.5*m* ( vf^2 - vi^2 ) = m*g*(R - R*cos(θ))
( vf^2 - vi^2 ) = 2*g*R*( 1 - cos(θ))
vi^2 = vf^2 - 2*g*R*( 1 - cos(θ))
vi^2 = 38.708 - 2*32.2*1.45*(1-cos(34))
vi^2 = 22.744
vi = 4.77 ft/s
A particle of mass m is confined to a box of length`. Its initial wave function is identical to that of the displacement of the string in the problem above, Boas Ch. 13, Sec. 4, #4.Find the solution of the Schrodinger equation
Answer:
φ = √2/L sin (kx), E = (h² / 8 mL²) n²
Explanation:
The Schrödinger equation for a particle in a box is, described by a particle within a potential for simplicity with infinite barrier
V (x) = ∞ x <0
0 0 <x <L
∞ x> L
This means that we have a box of length L
We write the equation
(- h’² /2m d² / dx² + V) φ = E φ
h’= h / 2π
The region of interest is inside the box, since being the infinite potential there can be no solutions outside the box. The potential is zero
- h’² /2m d²φ/ dx² = E φ
The solution for this equation is a sine wave,
Because it is easier to work with exponentials, let's use the reaction between the sine function and cook with the exponential
[tex]e^{ikx}[/tex] = cos kx + i sin kx
Let's make derivatives
dφ / dx = ika e^{ikx}
d²φ / dx² = (ik) e^{ikx} = - k² e^{ikx}
Let's replace
- h'² / 2m (-k² e^{ikx}) = E e^{ikx}
E = h'² / 2m k²
To have a solution this expression
Now let's work on the wave function, as it is a second degree differential bond, two solutions must be taken
φ = A e^{ikx} + B e^{-ikx}
This is a wave that moves to the right and the other to the left.
Let's impose border conditions
φ (0) = 0
φ (L) = 0
For being the infinite potential
With the first border condition
0 = A + B
A = -B
They are the second condition
0 = A e^{ikL}+ B e^{-ikL}
We replace
0 = A (e^{ikL} - e^{-ikL})
We multiply and divide by 2i, to use the relationship
sin kx = (e^{ikx} - e^{-ikx}) / i2
0 = A 2i sin kL
Therefore kL = nπ
k = nπ / L
The solution remains
φ = A sin (kx)
E = (h² / 8 mL²) n²
To find the constant A we must normalize the wave function
φ*φ = 1
A² ∫ sin² kx dx = 1
We change the variable
sin² kx = ½ (1 - cos 2kx)
A =√ 2 / L
The definitive function is
φ = √2/L sin (kx)
An ideal gas Carnot cycle with air in a piston cylinder has a high temperature of 1000 K and a heat rejection at 400 K. During the heat addition the volume triples. Find the two specific heat transfers (q) in the cycle and the overall cycle efficiency
Answer:
W / n = - 9133 J / mol, W / n = 3653 J / mol , e = 0.600
Explanation:
The Carnot cycle is described by
[tex]e= 1 - Q_{c} / Q_{H} = 1 - T_{c} / T_{H}[/tex]
In this case they indicate that the final volume is
V = 3V₀
In the part of the heat absorption cycle from the source is an isothermal expansion
W = n RT ln (V₀ / V)
W / n = 8.314 1000 ln (1/3)
W / n = - 9133 J / mol
During the part of the isothermal compression in contact with the cold focus, as in a machine the relation of volumes is maintained in this part is compressed three times
W / n = 8.314 400 (3)
W / n = 3653 J / mol
The efficiency of the cycle is
e = 1- 400/1000
e = 0.600
Air "breaks down" when the electric field strength reaches 3 × 106 N/C, causing a spark. A parallel-plate capacitor is made from two 3.0 cm × 3.0 cm electrodes.How many electrons must be transferred from one electrode to the other to create a spark between the electrodes?
Answer:
[tex]1.5\times 10^{11}}[/tex]
Explanation:
We are given that
Electric field=[tex]E=3\times 10^6 N/C[/tex]
Dimension of parallel plate capacitor=[tex]3 cm\times 3 cm[/tex]
Area of parallel plate capacitor=[tex]A=3\times 3=9 cm^2=9\times 10^{-4}m^2[/tex]
[tex]1 cm^2=10^{-4} m^2[/tex]
We have to find the number of electrons must be transferred from one electrode to the other to create a spark between the electrodes.
[tex]E=\frac{Q}{\epsilon_0A}[/tex]
Where [tex]\epsilon_0=8.85\times 10^{-12}C^2/Nm^2[/tex]
Substitute the values
[tex]3\times 10^6=\frac{Q}{8.85\times 10^{-12}\times 9\times 10^{-4}}[/tex]
[tex]Q=3\times 10^6\times 8.85\times 10^{-12}\times 9\times 10^{-4}}[/tex]
[tex]Q=2.4\times 10^{-8} C[/tex]
We know that
[tex]Q=ne=n\times 1.6\times 10^{-19} [/tex]
Where e=[tex]1.6\times 10^{-19} C[/tex]
[tex]n=\frac{Q}{e}=\frac{2.4\times 10^{-8}}{1.6\times 10^{-19}}=1.5\times 10^{11}}[/tex]
If the frequency of the radio station is 88.1MHz(8.81 •10^7Hz), what is the wavelength of the wave used by the radio station for its broadcast? The answer should have three significant figures
Answer:
3.41m
Explanation:
The following were obtained from the question:
f (frequency) = 8.81x10^7Hz
V (velocity of electromagnetic wave) = 3x10^8 m/s
λ (wavelength) =?
Velocity, frequency and wavelength of a wave are related with the equation below:
V = λf
λ = V/f
λ = 3x10^8 /8.81x10^7
λ = 3.41m
Therefore, the wavelength of the radio wave is 3.41m
Answer:
Answer: 3.41
Explanation:
Edge 2020 (E2020)
If the dielectric constant is 14.1, calculate the ratio of the charge on the capacitor with the dielectric after it is inserted as compared with the initial charge.
Answer:
[tex]\frac{Q}{Q_0}=1[/tex]
Explanation:
Capacitance is defined as the charge divided in voltage.
[tex]C=\frac{Q}{V}(1)[/tex]
Introducing a dielectric into a parallel plate capacitor decreases its electric field. Therefore, the voltage decreases, as follows:
[tex]V=\frac{V_0}{k}[/tex]
Where k is the dielectric constant and [tex]V_0[/tex] the voltage of the capacitor without a dielectric
The capacitance with a dielectric between the capacitor plates is given by:
[tex]C=kC_0[/tex]
Where k is the dielectric constant and [tex]C_0[/tex] the capacitance of the capacitor without a dielectric. So, we have:
[tex]Q=CV\\Q=kC_0\frac{V_0}{k}\\Q=C_0V_0\\Q_0=C_0V_0\\Q=Q_0\\\frac{Q}{Q_0}=1[/tex]
Therefore, a capacitor with a dielectric stores the same charge as one without a dielectric.
A remote-controlled car’s wheel accelerates at 22.7 rad/s2 . If the wheel begins with an angular speed of 10.3 rad/s, what is the wheel’s angular speed after exactly twenty full turns
Explanation:
Below is an attachment containing the solution.
A factory worker pushes a crate of mass 31.0 kg a distance of 4.35 m along a level floor at constant velocity by pushing horizontally on it. The coefficient of kinetic friction between the crate and floor is 0.26.
a. What magnitude of force must the worker apply?
b. How much work is done on the crate by this force?
c. How much work is done on the crate by friction?
d. How much work is done on the crate by the normal force? By gravity?
e. What is the total work done on the crate?
Answer:
a. 79.1 N
b. 344 J
c. 344 J
d. 0 J
e. 0 J
Explanation:
a. Since the crate has a constant velocity, its net force must be 0 according to Newton's 1st law. The push force [tex]F_p[/tex] by the worker must be equal to the friction force [tex]F_f[/tex] on the crate, which is the product of friction coefficient μ and normal force N:
Let g = 9.81 m/s2
[tex]F_p = F_f = \mu N = \mu mg = 0.26 * 31 * 9.81 = 79.1 N[/tex]
b. The work is done on the crate by this force is the product of its force [tex]F_p[/tex] and the distance traveled s = 4.35
[tex]W_p = F_ps = 79.1*4.35 = 344 J[/tex]
c. The work is done on the crate by friction force is also the product of friction force and the distance traveled s = 4.35
[tex]W_f = F_fs = -79.1*4.35 = -344 J[/tex]
This work is negative because the friction vector is in the opposite direction with the distance vector
d. As both the normal force and gravity are perpendicular to the distance vector, the work done by those forces is 0. In other words, these forces do not make any work.
e. The total work done on the crate would be sum of the work done by the pushing force and the work done by friction
[tex]W_p + W_f = 344 - 344 = 0 J[/tex]
Answer:
(A) 79N
(B) W = 344J
(C) Wf= -344J
(D) W = 0J
(E) W = 0J
Explanation:
Please see attachment below.
You accidentally drop a quarter into the hot coals of a campfire. You fish out the hot quarter with a pair of pliers and drop the quarter directly on top of a large 2 kg block of ice to cool it down. In what direction does heat flow:
There is no heat flow.
From the quarter to the block of ice
Answer:
from the quarter to the block of ice
Explanation:
Heat flows from higher temperature to lower temperature until temperature of both bodies are in Equilibrium .
Since block of ice has lower temperature than that of quarter. heat transfer will take from quarter to ice until both have same temperature(in other words temperature are in Equilibrium for quarter and ice)
Final answer:
Heat will flow from the hot quarter to the block of ice as heat always transfers from a warmer object to a cooler one. The ice absorbs the heat and may melt without increasing in temperature due to the phase change.
Explanation:
When a hot quarter is dropped onto a large block of ice, heat will flow from the quarter to the block of ice. This is because heat always flows spontaneously from a hotter object to a cooler one according to thermodynamics. In this case, the hot quarter would lose heat, and the block of ice would absorb it. Even as the ice absorbs heat, it may not increase in temperature as it may be undergoing a phase change from solid to liquid at 0°C. The heat is used to break the bonds between water molecules during the melting process, thus increasing the internal potential energy instead of increasing the kinetic energy, which would raise the temperature.
Say you have two parallel current-carrying wires, each carrying a current of 1.0 A and with a distance of 1.0 m between them. What is the magnitude of the force per unit length experienced by each wire
Answer:
[tex]\dfrac{F}{l}=2\times 10^{-7}\ N/m[/tex]
Explanation:
Given,
current in the wire I₁ = 1 A
I₂ = 1 A
distance between them, r = 1 m
using Force per unit length formula
[tex]\dfrac{F}{l}=\dfrac{\mu_0I_1I_2}{2\pi r}[/tex]
[tex]\mu_0 = magnetic\ permeability\ of\ free\ space = 4\pi\times 10^{-7}[/tex]
[tex]\dfrac{F}{l}=\dfrac{4\pi \times10^{-7}\times 1\times 1}{2\pi\times 1}[/tex]
[tex]\dfrac{F}{l}=2\times 10^{-7}\ N/m[/tex]
Hence, the magnitude of force per unit length is equal to [tex]\dfrac{F}{l}=2\times 10^{-7}\ N/m[/tex]
Final answer:
The magnitude of the force per unit length each 1.0 A current-carrying wire experiences when separated by a distance of 1.0 m is 2 x 10⁻⁷ N/m, calculated using the formula for magnetic force between parallel conductors.
Explanation:
When discussing two parallel current-carrying wires, we're addressing the magnetic force that arises between them due to their currents. Specifically, when each wire carries a current of 1.0 A and they are placed 1.0 m apart, the force per unit length that each wire experiences can be calculated using the formula for the magnetic force between two parallel conductors. The equation is FE = (µ0 / 2π) × (I1I2 / r), where µ0 is the magnetic constant (4π x 10-7 T·m/A), I1 and I2 are the currents in the wires, and r is the distance between the wires. Given that each wire carries 1.0 A of current and the separation is 1.0 m, we can plug these values into the formula to find that FE = (4π x 10-7 T·m/A / 2π) × (1.0 A2 / 1.0 m), resulting in a force per unit length of 2 x 10-7 N/m.
A SMA wire in the un-stretched condition is then given an initial strain of εo (to preload the wire) at room temperature (RT). Its ends are then rigidly fixed. What force is developed in the wire?
Answer: tensional force
Explanation:
Tension force on a material occurs when two equal forces act on a material in an opposite direction away from the ends of the material.
Pre-tensing a wire material increases its load bearing capacity and reduces its flexure.
Two 3.0 μC charges lie on the x-axis, one at the origin and the other at What is the potential (relative to infinity) due to these charges at a point at on the x-axis?
Complete Question:
Two 3.0µC charges lie on the x-axis, one at the origin and the other at 2.0m. A third point is located at 6.0m. What is the potential at this third point relative to infinity? (The value of k is 9.0*10^9 N.m^2/C^2)
Answer:
The potential due to these charges is 11250 V
Explanation:
Potential V is given as;
[tex]V =\frac{Kq}{r}[/tex]
where;
K is coulomb's constant = 9x10⁹ N.m²/C²
r is the distance of the charge
q is the magnitude of the charge
The first charge located at the origin, is 6.0 m from the third charge; the potential at this point is:
[tex]V =\frac{9X10^9 X3X10^{-6}}{6} =4500 V[/tex]
The second charge located at 2.0 m, is 4.0 m from the third charge; the potential at this point is:
[tex]V =\frac{9X10^9 X3X10^{-6}}{4} =6750 V[/tex]
Total potential due to this charges = 4500 V + 6750 V = 11250 V
The potential due to two 3.0 μC charges on the x-axis at different distances from a point can be calculated using Coulomb's Law.
Explanation:The potential due to two point charges can be found using Coulomb's Law. The potential, V, at a point on the x-axis is the sum of the potentials from each charge. The potential due to a point charge can be calculated using the formula V = k * (Q / r), where k is the electrostatic constant, 9 x 10^9 Nm^2/C^2, Q is the charge, and r is the distance between the charge and the point. In this case, since the charges are on the x-axis, the distance between the origin and the point is x, and the distance between the other charge and the point is (6-x). So, the potential at the point is V = k * (3.0 x 10^-6 / x) + k * (3.0 x 10^-6 / (6-x)) relative to infinity.
Learn more about potential here:
https://brainly.com/question/28300184
#SPJ3
A 20.0-kg cannonball is fired from a cannon with muzzle speed of 1 000 m/s at an angle of 37.08 with the horizontal. A second ball is fired at an angle of 90.08. Use the isolated system model to find (a) the maximum height reached by each ball and (b) the total mechanical energy of the ball–Earth system at the maximum height for each ball. Let y5 0 at the cannon.
Answer:
(a). The maximum height by first ball is [tex]1.8545\times10^{4}\ m[/tex]
The maximum height by second ball is [tex]5.1020\times10^{4}\ m[/tex]
(b). The total mechanical energy of the ball–Earth system at the maximum height for each ball is [tex]1.0\times10^{7}\ J[/tex]
Explanation:
Given that,
Mass of cannonball = 20.0 kg
Speed = 1000 m/s
Angle with horizontal= 37.08
Fired angle = 90.08
We need to calculate the speed of the ball
Using formula of speed
[tex]v_{y}=v\sin\theta_{H}[/tex]
Put the value into the formula
[tex]v_{y}=1000\times\sin37.08[/tex]
[tex]v_{y}=602.9\ m/s[/tex]
(a). We need to calculate the maximum height by first ball
Using conservation of energy
[tex]\dfrac{1}{2}mv^2=mgh[/tex]
[tex]h= \dfrac{v^2}{2g}[/tex]
Put the value into the formula
[tex]h=\dfrac{(602.9)^2}{2\times9.8}[/tex]
[tex]h=1.8545\times10^{4}\ m[/tex]
We need to calculate the maximum height by second ball
Using conservation of energy
[tex]\dfrac{1}{2}mv^2=mgh[/tex]
[tex]h= \dfrac{v^2}{2g}[/tex]
Put the value into the formula
[tex]h=\dfrac{(1000)^2}{2\times9.8}[/tex]
[tex]h=5.1020\times10^{4}\ m[/tex]
(b). We need to calculate the total mechanical energy of the ball–Earth system at the maximum height for each ball
Using formula of energy
[tex]E=\dfrac{1}{2}mv^2[/tex]
[tex]E=\dfrac{1}{2}\times20\times1000^2[/tex]
[tex]E=1.0\times10^{7}\ J[/tex]
Hence, (a). The maximum height by first ball is [tex]1.8545\times10^{4}\ m[/tex]
The maximum height by second ball is [tex]5.1020\times10^{4}\ m[/tex]
(b). The total mechanical energy of the ball–Earth system at the maximum height for each ball is [tex]1.0\times10^{7}\ J[/tex]
Singly charged positive ions are kept on a circular orbit in a cyclotron. The magnetic field inside the cyclotron is 1.833 T. The mass of the ions is 2.00×10-26 kg, and speed of the ions is 2.05 percent of the speed of the light. What is the diameter of the orbit? (The speed of the light is 3.00×108 m/s.)
Answer:
The diameter is 0.8376 m
Explanation:
Magnetic force is the force that is associated with the magnetic field, the magnitude of the magnitude force can be obtained using equation 1;
F = q v B .....................................1,
where q is the magnitude of the charge of the particle =;
v is the velocity and;
B is the magnetic field = 1.833 T ;
Here, the path of the charge is circular so the force can be also considered as the centripetal force which is represented in equation 2;
[tex]F_{c}[/tex] = m [tex]v^{2}[/tex] / r ....................................2,
m is the particle's mass = 2.00 x[tex]10^{-26}[/tex] kg
v is the speed of ion = 2.05% of 3.00 x [tex]10^{8}[/tex] = 0.0205 x 3.00 x [tex]10^{8}[/tex]
= 6.15 x [tex]10^{6}[/tex] m/s ;
Singly charged ion has a charge equal to the electron charge and the magnitude = 1.60217646 ×[tex]10^{-19}[/tex] C and;
r is the radius of the circular path.
to get the diameter of the orbit we equate equation 1 to 2 and isolate r in equation 2.
q v B = m [tex]v^{2}[/tex] / r
r = m v/q B.....................................3
r = (2.00 x[tex]10^{-26}[/tex] kg) x (6.15 x [tex]10^{6}[/tex] m/s) / (1.60217646 ×[tex]10^{-19}[/tex] C) x (1.833 T)
r = 0.4188 m
The diameter is r x 2
D = 0.4188 m x 2
D = 0.8376 m
Therefore the diameter is 0.8376
g Case 1, a mass M M hangs from a vertical spring having spring constant k , k, and is at rest at its equilibrium height. In Case 2, the same mass has been lifted a distance D D vertically upward. If the potential energy in Case 1 is defined to be zero, what is the potential energy in Case 2
In the scenario described, increasing the height of a mass M in a vertical spring-mass system will result in both gravitational and spring potential energy. Thus, the potential energy in Case 2 is the sum of gravitational potential energy (m*g*D) and the elastic potential energy of the spring (1/2*k*D^2).
Explanation:The situation described in the question deals with principles of Physics, specifically potential energy and its application to the spring-mass system. Consider both cases with the mass M hanging from a spring with a constant k in a vertical orientation. In the first case, the system is at equilibrium and thus the potential energy is defined as zero.
In the second case, the mass M is lifted upward a vertical distance D from the equilibrium position, it now possesses gravitational potential energy in addition to the elastic potential energy of the spring. This total energy is preserved as long as no external force behaves on the system. The gravitational potential energy gained by the mass is equal to m*g*D where m is the mass, g is the acceleration due to gravity and D is the vertical distance lifted.
The potential energy stored in the spring when it is stretched or compressed by a distance 'x' is given by the formula U = 1/2*k*x^2, where 'k' is the spring constant and 'x' is the displacement from the equilibrium position (in this case is D).
So, combining both energies, the total potential energy in Case 2, when the mass has been lifted a vertical distance D is m*g*D + 1/2*k*D^2.
Learn more about Potential Energy here:https://brainly.com/question/24284560
#SPJ12
A parallel-plate capacitor is constructed from two aluminum foils of 1 square centimeter area each placedon both sides of a rubber square of the same size. The rubber dielectric is 2.5 mm thick, hasr2.5, andbreakdown field strength of 25 megavolts per meter. Find the voltage rating of the capacitor using a safetyfactor of 10.
Answer:
The voltage will be 0.0125V
Explanation:
See the picture attached
You are generating traveling waves on a stretched string by wiggling one end. If you suddenly begin to wiggle more rapidly without appreciably affecting the tension, you will cause the waves to move down the string a. faster than before.b. at the same speed as before.c. slower than before.
Answer:
Option as B is correct At the same speed as before
Explanation:
As we know the relation between speed of the wave and tension in string
The speed of wave in stretched string
ν = [tex]\sqrt{\frac{T}{\mu} }[/tex]
speed of wave is the directly proportional to the square root of tension as mentioned in question tension of string is unaffected when in linear mass density is constant, so we can say that the speed of wave will be the same
Option as B is correct At the same speed as before
If you suddenly begin to wiggle more rapidly without appreciably affecting the tension, you will cause the waves to move down the string at the same speed as before (Option b).
What is a wave?A wave can be defined as a type of disturbance that contains energy independently of particle motion.
The wave can move at a velocity (frequency) that is directly proportional to the tension.In this case, tension is constant, thereby velocity of the wave will remain constant.In conclusion, if you suddenly begin to wiggle more rapidly without appreciably affecting the tension, you will cause the waves to move down the string at the same speed as before (Option b).
Learn more in:
https://brainly.com/question/12215474
What is the voltage across six 1.5-V batteries when they are connected (a) in series, (b) in parallel, (c) three in parallel with one another and this combination wired in series with the remaining three?
The resultant voltage depends on the arrangement of the batteries. For series configuration, the voltage sums up to 9V. For parallel, it remains 1.5V. And for combined series and parallel, it sums up to 3V.
Explanation:The voltage across batteries depends on how they are connected.
When the batteries are connected in series, the voltages add up. So, for six 1.5-V batteries, the total voltage is 6 * 1.5V = 9V. When the batteries are connected in parallel, the voltage remains the same as one battery, which is 1.5V, no matter how many batteries are connected. If three batteries are connected in parallel with each other and then in series with the remaining three also organized in parallel, the voltage would be 1.5V (parallel group) + 1.5V (parallel group) = 3V.Learn more about Voltage here:https://brainly.com/question/31347497
#SPJ3
Analyzing the Light Bulb: You should have noticed that the light bulb doesn't have a single well-defined "resistance," since the current vs. voltage plot is nonlinear. Nevertheless, one can define a "voltage-dependent resistance" as R(V)=V/I(V)as the ratio of voltage to current.1Basic Behavior: According to your data, does this resistance increase or decrease with voltage? A reasonable (and correct) thought is that the impact is really with temperature, as the light bulb heats up with more power going into it. How does your data imply resistance varies with temperature?Thermal Expansion: One hypothesis you might have is that the reason is that the resistor expands slightly with increased temperature (since most materials do), and hence the cross-sectional area and length of the resistor change.Supposing the resistor increases in size by the same factor in every direction, what direction does the resistance change? (I.e., does the resistance get larger or smaller?) Is this the direction that you expect based on your answer to the previous part?
Answer:
Resistance increases with increase in temperature which depends on power supplied which also depends on voltage.
Thermal expansion will make resistance larger.
Explanation:
Light bulb is a good example of a filament lamp. If we plot the graph of voltage against current we will notice that resistance is constant at constant temperature.
The filament heats up when an electric current passes through it, and produces light as a result.
The resistance of a lamp increases as the temperature of its filament increases. The current flowing through a filament lamp is not directly proportional to the voltage across it.
tensile stress begins to appear in resistor as the temperature rises. Thus, the resistance value increases as the temperature rises. Resistance value can only decrease as the temperature rises in case of thin film resistor with aluminium substrate.
In case of a filament bulb, the resistance will increase as increase in length of the wire. The thermal expansion in this regard is linear expansivity in which resistance is proportional to length of the wire.
Resistance therefore get larger.
The op amp in this circuit is ideal. R3 has a maximum value of 100 kΩ and σ is restricted to the range of 0.2 ≤ σ ≤ 1.0. a. Calculate the range of vO if vI = 40 mV. b. If σ is not restricted, at what value of σ will the operational amplifier saturate?
I have attached the circuit image missing in the question.
Answer:
A) The range of vo is; -6.6V≤ vo ≤-1V
B) σ = 0.1861
Explanation:
A) First of all, Let VΔ be the voltage from the potentiometer contact to the ground.
Thus; [(0 - vg)/(2000)] +[(0 - vΔ)/(50,000)] = 0
So, [(- vg)/(2000)] +[(- vΔ)/(50,000)] = 0
Simplifying further; -25 vg - vΔ = 0
From the question, vg = 40mV = 0.04 V
So - 25(0.04) = vΔ
So: vΔ = - 1 V
Now, [vΔ/(σRΔ)] + [(vΔ - 0)/(50,000)] + [(vΔ - vo)/((1 - σ)RΔ))] = 0
So, multiplying each term by RΔ to get; [vΔ/(σ)] + [(vΔ x RΔ)/(50,000)] + [(vΔ - vo)/((1 - σ))] = 0
So RΔ = 100kΩ or 100,000Ω from the question.
So, substituting for RΔ, we get,
[vΔ/(σ)] + [2vΔ] + [(vΔ - vo)/((1 - σ))] = 0
Let's put the value of - 1 for vΔ as gotten before.
So, ( - 1/σ) - 2 + [(-1 - vo)/(1 - σ)] = 0
Now let's make vo the subject of the equation to get;
-1 - vo = (1 - σ)[2 + (1/σ)]
-1 - vo = 2 - 2σ + (1/σ) - 1
-vo = 1 + 2 - 2σ + (1/σ) - 1
-vo = 2 - 2σ + (1/σ)
vo = - 1 (2 - 2σ + (1/σ))
When σ = 0.2; vo = - 1(2 - 0.4 + 5) =
- 1 x 6.6 = - 6.6V
Also when σ = 1;
vo = - 1(2 - 2 + 1) = - 1V
Therefore, the range of vo is;
- 6.6V ≤ vo ≤ - 1V
B) it will saturate at vo = - 7V
So, from;
vo = - 1 (2 - 2σ + (1/σ))
-7 = - 1 (2 - 2σ + (1/σ))
Divide both sides by (-1)
7 = (2 - 2σ + (1/σ))
Now, subtract 2 from both sides to get; 5 = - 2σ + (1/σ)
Multiply each term by α to get;
5σ = - 2σ^(2) + 1
So 2σ^(2) + 5σ - 1 = 0
Solving simultaneously and picking the positive value , we get σ to be approximately 0.1861
Final answer:
The question involves understanding an ideal operational amplifier's output behavior, focusing on its output voltage changes and saturation with respect to variations in σ (sigma). Calculations for the output voltage range given a specific input and understanding the conditions under which the op-amp will saturate are key.
Explanation:
The question revolves around an operational amplifier (op-amp) circuit, exploring its behavior under certain conditions, specifically examining output voltage (vO) variations and saturation point related to the parameter σ (sigma). The op-amp is assumed to be ideal, implying infinite gain, zero input current, and that its input terminals are at the same potential.
a. Range of vO if vI = 40 mV
Given that the op-amp is ideal, the output voltage will depend on the input voltage (vI), the gain settings (σ), and the feedback resistor (R3). In practical scenarios, the gain can be adjusted by changing the value of σ or R3. However, for an ideal op-amp, the input voltage is directly proportional to the output voltage, influenced by σ. With vI = 40 mV and σ ranging between 0.2 and 1.0, the output voltage will vary accordingly, directly proportional to these parameters.
b. Saturation point of the op-amp
Saturation in an op-amp occurs when the output voltage exceeds the power supply limits, meaning the op-amp can no longer amplify the input signal. The specific value of σ at which saturation occurs depends on the supply voltage, the op-amp's maximum output voltage capability, and the configuration of the feedback network. Without specific values for the power supply or feedback network, calculating the exact σ value for saturation is not possible. Yet, in theory, as σ approaches the op-amp's gain limit or if the gain results in an output voltage beyond what the op-amp can deliver based on its power supply, saturation will occur.
If a trapeze artist rotates 1 each second while sailing through the air, and contracts to reduce her rotational inertia to 0.40 of what it was, how many rotations per second will result?
Explanation:
A trapeze is rotating with 1 rotation per second .
Thus its angular velocity ω = 2π n
here n is the number of rotations per second
Thus ω = 2π b because n = 1 in this case
Suppose the moment of inertia of his is = I
Then angular momentum L₁ = I ω = 2 I π
In the second case , the moment of inertia becomes = 0.4 I
Let his angular velocity is ω₀
Thus angular momentum L₂ = 0.4 I ω₀
Because no external torque is applied , therefore angular momentum will remain constant .
Thus L₁ = L₂
Therefore 2 I π = 0.4 I x 2 n₀ π
here n₀ is the number of rotations per second
n₀ = [tex]\frac{1}{0.4}[/tex] = [tex]\frac{5}{2}[/tex] = 2.5
A truck runs into a pile of sand, moving 0.80 m as it slows to a stop. The magnitude of the work that the sand does on the truck is 5.5×105J. Part A Determine the magnitude of the average force that the sand exerts on the truck
Answer:
687,500 N
Explanation:
Workdone = Force × Distance
Making force the subject of the formula; we have:
Force =[tex]\frac{workdone}{distance}[/tex]
Given that:
workdone = 5.5×10⁵ J
Distance = 0.80 m
∴ Force = [tex]\frac{5.5*10^5}{0.8}[/tex]
Force = 687,500 N
Answer:
6.875×10⁵ N.
Explanation:
Force: This can be defined as the product of mass and acceleration or it can be defined as the ratio of work done and distance. The S.I unit of force is Newton.
W = F×d................. Equation 1
Where W = work done, F = force, d = distance.
make F the subject of the equation
F = W/d.................... Equation 2
Given: W = 5.5×10⁵ J, d = 0.8 m
Substitute into equation 2
F = 5.5×10⁵ /0.8
F = 6.875×10⁵ N.
Hence the force exerted on the truck by the sand = 6.875×10⁵ N.
The driving force for fluid flow is the pressure difference, and a pump operates by raising the pressure of a fluid (by converting the mechanical shaft work to flow energy). A gasoline pump is measured to consume 3.8 kW of electric power when operating, If the pressure differential between-the outlet and inlet of the pump is measured to be 7 kPa and the changes in velocity and elevation are negligible, determine the maximum possible volume flow rate of gasoline.
Answer:
[tex]\dot V = 0.542 \frac{m^{3}}{s}[/tex]
Explanation:
The power needed for the pump to raise the pressure of gasoline is defined by following equation. The maximum possible volume flow rate is isolated and then calculated:
[tex]\dot W = \dot V \cdot \Delta P\\\dot V = \frac{\dot W}{\Delta P}\\\dot V = \frac{3.8 kW}{7 kPa}\\\dot V = 0.542 \frac{m^{3}}{s}[/tex]
Explanation:
Below is an attachment containing the solution.
The element hydrogen has the highest specific heat of all elements. At a temperature of 25°C, hydrogen’s specific heat capacity is 14300J/(kg K). If the temperature of a .34kg sample of hydrogen is to be raised by 25 K, how much heat will have to be transferred to the hydrogen?
Answer:
121550 J
Explanation:
Parameters given:
Mass, m = 0.34kg
Specific heat capacity, c = 14300 J/kgK
Change in temperature, ΔT = 25K
Heat gained/lost by an object is given as:
Q = mcΔT
Since ΔT is positive in this case and also because we're told that heat was transferred to the hydrogen sample, the hydrogen sample gained heat. Therefore, Q:
Q = 0.34 * 14300 * 25
Q = 121550J or 121.55 kJ