A parallel circuit has a total current of 4 Amperes and an equivalent resistance of .5 Ohms. What is the power in this circuit?

Using the combined gas law, we can find that the new volume of the gas would be approximately 22.62 L.

In order to find the new volume of the gas when the pressure is increased to 250 kPa and the temperature is decreased to 0°C, we can use the combined gas law.

The combined gas law states that for a given amount of gas, the ratio of pressure, volume, and temperature remains constant:

P1V1/T1 = P2V2/T2

Plugging in the values given in the question, we have:

200 kPa * 25 L / (25 + 273) K = 250 kPa * V2 / (0 + 273) K

Simplifying and solving for V2, we find:

V2 = (200 kPa * 25 L * 273 K) / (250 kPa * (25 + 273) K)

V2 ≈  22.62 L

Answer:

Although graphite and diamond are both composed of carbon atoms, their physical properties are very different. The differences are the result of the atomic structures of the minerals. In graphite the carbon atoms are arranged in layers. As a result, graphite is soft. The great hardness of diamond is the result of the bonds that hold carbon atoms in a network structure.

Explanation:

Answer:

9090 m, 104 s

Explanation:

After the acceleration phase, the rocket reaches a height of:

x = x₀ + v₀ t + ½ at²

x = (0 m) + (0 m/s) (30 s) + ½ (10 m/s²) (30 s)²

x = 4500 m

And it reaches a velocity of:

v = at + v₀

v = (10 m/s²) (30 s) + (0 m/s)

v = 300 m/s

After the fuel runs out, the rocket goes into free fall.  The maximum height reached is:

v² = v₀² + 2a(x - x₀)

(0 m/s)² = (300 m/s)² + 2(-9.8 m/s²)(x - 4500 m)

x ≈ 9090 m

The time to reach maximum height during free fall:

v = at + v₀

0 m/s = (-9.8 m/s²) t + (300 m/s)

t ≈ 30.6 s

And the time to land from the maximum height:

x = x₀ + v₀ t + ½ at²

0 m = (9090 m) + (0 m/s) t + ½ (-9.8 m/s²) t²

t ≈ 43.1 s

So the total time is:

t = 30 s + 30.6 s + 43.1 s

t ≈ 104 seconds

Answer:

B. virtual

Explanation:

Answer on edge 2020

Virtual is referred to the area which is marked as X and is denoted as option B.

This is defined as an upright image which is formed where the rays seem to diverge.

Both concave and convex lenses produces a virtual image which was why it was chosen as the most appropriate choice.

Read more about Virtual image here https://brainly.com/question/9861899

#SPJ2

Hey there!

The answer is that The data was not reliable because there was not any repetition.

An experiment should be completed multiple times to be sure of accurate results.

A screenshot is attached.

Hope this helps! :)

Answer:

Actually, Kaylene M., the correct answer was D. You know:"The data is not reliable because there was not any repetition." The answer you have "screenshoted" I got the question wrong because of you. Thanks a lot.

Explanation:

Answer:

Lowest

Explanation:

Law of superposition

The correct answer is A) lowermost.

The principle of superposition states that in an undisturbed sequence of sedimentary rocks, each layer is younger than the one below it and older than the one above it.

This means that the oldest fossils would be found in the lowermost layer of sedimentary rock, as it was deposited first. Over time, newer layers of sediment accumulate on top, preserving the older layers and the fossils they contain.

Therefore, the oldest fossils would be located in the oldest layer, which is the lowermost one. Options B, C, and D would contain progressively younger fossils, with the uppermost layer containing the youngest fossils.

The stratosphere (option C) is not a layer of rock but rather a layer of Earth's atmosphere, making it an incorrect choice for finding fossils."

Answer:

110

Explanation:

The net charge of the compound is the sum of the net charges due to the electrons and the protons:

[tex]Q=N_p q_p + N_e q_e[/tex]

where

Np is the number of protons

Ne = 50 is the number of electrons

[tex]N_p = +1.6\cdot 10^{-19} C[/tex] is the charge of each proton

[tex]N_e = -1.6\cdot 10^{-19} C[/tex] is the charge of each electron

[tex]Q=+9.6\cdot 10^{-18} C[/tex] is the net charge of the compound

Solving the equation for Np, we find the number of protons:

[tex]N_p = \frac{Q-N_e q_e}{q_p}=\frac{+9.6\cdot 10^{-18}C-(50)(-1.6\cdot 10^{-19}C)}{+1.6\cdot 10^{-19} C}=110[/tex]

Answer:

1225 J

Explanation:

The Gravitational potential energy (PEG) gained by a mass lifted above the ground is given by

[tex]PE=mgh[/tex]

where

m is the mass

g = 9.8 m/s^2 is the acceleration due to gravity

h is the height at which the object has been lifted

In this problem, we have

m = 250 kg

h = 0.5 m

So, the PE of the object is

[tex]PE=(250 kg)(9.8 m/s^2)(0.5 m)=1225 J[/tex]

Answer:

1225J

Explanation:

The Gravitational potential energy (PEG) gained by a mass lifted above the ground is given by

where

m is the mass

g = 9.8 m/s^2 is the acceleration due to gravity

h is the height at which the object has been lifted

In this problem, we have

m = 250 kg

h = 0.5 m

So, the PE of the object is

1225J

Answer:

Its from a reflection of sound waves against a hard surface

Explanation:

Answer:

Explanation:

Velocity:

Formula : displacement/time

SI unit : m/s

Acceleration :

Formula: change in Velocity/time

SI unit : m/s²

Force:

Formula: mass x acceleration due to gravity

SI unit: N(newton)

Mass:

SI unit: kilogram(kg)

Answer:

1. The SI units for measuring the velocity of the car: meters per second

2.The SI units for measuring the acceleration of the car:meters per secend squared

3.The SI units of measuring force:Newton’s

4.The SI units for measuring mass:kilograms

These are the correct answers on Ed

Answer:

7.0 m/s

Explanation:

The question is on Free-Fall

In a free fall, an object falls freely without only gravity acting on it. Velocity at the top is zero m/s

Height of fall, h=1/2gt²

Velocity, v=gt where g is gravity acceleration=9.8m/s² and t is time taken fall the fall

Finding the t taken for the fall;

h=2.5m but we know h=1/2gt²⇒substitute values in this equation

2.5=1/2×g×t²

2.5=1/2×9.8×t²⇒2.5=4.9t²

make t subject of the equation;

t²=2.5/4.9

t=√2.5/4.9 =0.7143sec

Finding the velocity

v=gt

v=9.8×0.7143=7m/s

I would say the answer is D

A hygrometer is an instrument used to measure relative humidity. ... To determine the relative humidity, the temperatures are taken from the dry-bulb thermometer and the temperature difference between the wet and dry bulb thermometers.

hygrometer is a weather instrument used to measure the amount of humidity in the atmosphere. There are two main types of hygrometers -- a dry and wet bulb psychrometer and a mechanical hygrometer.

The correct answer is D) relative humidity, and a sling psychrometer measures this by comparing the temperatures obtained from a wet and a dry thermometer.

A device that uses the wet/dry bulb method to measure the relative humidity is the sling psychrometer. This device consists of two thermometers, with one being the dry bulb and the other being the wet bulb. The difference in temperature readings between these two allows individuals to determine the relative humidity using a psychrometric chart, which requires a knowledge of the temperature at which air becomes saturated with water vapor (dew point) as well as other related properties of moist air.

The wet-bulb temperature is particularly important in industries such as textile, wood, and chemical processing, where humidity control is crucial. With the use of a psychrometric chart, these measurements enable precise control over the environmental conditions in plant production facilities and other industrial processes.

Answer:

A. All cells come from pre-existing cells

Explanation:

Francesco Redi's experiments aimed to test spontaneous generation, where life could emerge from non-living things. His first round included two groups of jars with raw meat in it. He covered one group with a thin cloth, allowing only air to get in, and the other group was left open.

In the jars left open, he noted maggots were present and the one that was covered contained no maggots.

The results indicated that the maggots only formed because flies laid their eggs on it and maggots developed. He did note that some maggots developed on the cloth itself, but on the outside.

Thus, he contributed in disproving spontaneous generation by showing that maggots only developed from the eggs that flies laid. This supports that all cells come from pre-existing cells.

Answer:

A)

Explanation:

Answer:

We know there's two forces acting on a book while it sits on a table:the force of gravity pulling it down, and the normal force of the table acting upward on the book.

Explanation:

Answer:

When the object is at rest, it stays in a balanced condition and so it does not tend to move from its current position unless an external force tend to act on it.  When the external force acts on it, there will be a displacement experienced by the object.

When a book is placed on a table, it does not move it is at rest and balanced position. So If you pick up a book from the floor and place it on the table. The potential energy of the book on the desk corresponds to the work required to move the book from the floor to the desk.

Answer: Absorbs and Increases

Explanation: As temperature of this substance rises from 20°C to 50°C, the substance absorbs heat and its kinetic energy increases.

Hopefully this help you. Have a great day. :)

Answer:

Absorbs, increases.

Explanation:

As we know that the amount of heat absorb or radiate is defined by a parameter called temperature. The change in temperature is defined as the heat absorb or radiate.

In the given situation, the temperature is increased from 20°C to 50°C, this is caused due to the substance's absorption of heat.

And the temperature is defined as the measurement of average kinetic energy of all the particles which are present in object. If any body or object temperature is increasing from 20°C to 50°C than its average velocity or movement of particle becomes fast. This will lead in increase of kinetic energy.

Yes! The Planet Jupiter is Magnetic

Answer: yes

Explanation:

It is surrounded by a giant magnetic field called the megnetophere

Question:

Which of these is a chemical property of a substance?

A) Density

B) Color

C) reactivity

D) melting point

Answer:

C) Reactivity

Explanation:

We  identify Reactivity as a chemical property because it dose Change to the chemical nature of matter such as change the way why the earth looks. One example of Reactivity is when we have earthquakes. But Things like Density, Melting point and color are signs of Physical properties because they do not change the chemical nature of matter.

The answer would be reactivity

A circle graph, or a pie chart is used to visualize information and data. A circle graph is used to easily show the results of an investigation in proportional manner. The arcs of a circle graph are prepositional to how many percent of population gave a certain answer

A circle graph is a graph in the form of a circle that's divided into pie pieces with each pie piece representing a part of the whole data set. In other words, each pie piece represents a percentage of the whole pie. Another word for a circle graph is a pie chart.

A circle graph is used to display data and it's used to recognize parts of a data set. It's useful to easily interpret what's going on in the scenario.

An example of a circle graph is provided in the image attached.

Answer:

1.28 m, 14 m/s

Explanation:

At the maximum height, the velocity is 0.

Given:

a = -9.8 m/s²

v₀ = 5.00 m/s

v = 0 m/s

x₀ = 0 m

Find:

x

v² = v₀² + 2a(x - x₀)

(0 m/s)² = (5.00 m/s)² + 2(-9.8 m/s²) (x - 0 m)

x = 1.28 m

The maximum speed is at the bottom of the well.

Given:

a = -9.8 m/s²

v₀ = 5.00 m/s

x₀ = 0 m

x = -8.5 m

Find:

v

v² = v₀² + 2a(x - x₀)

v² = (5.00 m/s)² + 2(-9.8 m/s²) (-8.5 m - 0 m)

v = -13.8 m/s

Rounded to 2 sig-figs, the maximum speed is 14 m/s.

Answer: it depends potential energy is the build up of kinetic energy like going to the top of a roller coaster. kintic is the use of the potential energy like going down the roller coaster so depends how much energy one another give :)

Hope this helps you out :)

Answer:

Explanation:

The question has no set meaning. Suppose you take a rock to the top of a building. You put the rock over the edge of the building. You don't drop it yet. The potential energy is greatest for the rock under this condition. The kinetic energy is 0 because the rock is not moving.

Now you let the rock go. As it falls, it looses distance to the ground which means that the Potential energy is nearing 0. The Kinetic energy is picking up because the rock is moving faster.

At the bottom of the rock's journey just before it hits the ground, the KE is at a maximum and the PE is nearly 0.

If you have fifty 15-ohm resistors all connected in parallel, their "effective" resistance is (15/50) = 0.3 ohms.

Current = (voltage) / (resistance)

Current = (115 V) / (0.3 ohm)

Current = 383.3 Amperes

This is an interesting question, with a VERRRRY interesting answer.  The fuse or circuit breaker that feeds the outlet where these lights are plugged in is most likely rated 15 or 20 or 25 Amperes, and it trips immediately.

But let's say it doesn't ... let's say the juice just keeps on flowing.

Power = (voltage) x (current)

These lights use energy at the rate of (115V)x(383.3A) = 44,083 watts.  This is roughly the same as the power used to run 22 toasters or 37 blow-dryers, all at the same time.  AND ... the lights are going to produce almost as much heat as 22 toasters or 37 blow-dryers all running at the same time.  The lights will probably burn the house down before long.

If electrical energy costs 20¢ per kilowatt-hour in this city, then running those lights for ONE HOUR is going to cost $8.82 !

All in all, it will be a good idea to unplug the Christmas tree lights when the family goes to bed.

The total current in the circuit when 50 parallel-connected 15-Ohm Christmas tree lights are connected to a 115VAC source is 383.5 A.

To calculate the total current of 50 parallel connected Christmas tree lights that each have 15 ohms of resistance connected to a source of 115 VAC we will apply Ohm's law which is I = V/R. Here I represents current V represents voltage and R represents resistance.

In a parallel circuit all the resistor leads on one side of the resistors are connected together and all the leads on the other side are connected together. Therefore each resistor in a parallel circuit has the same full voltage of the source applied to it. That said, each of the 50 15-ohm lights will experience the full 115 volts.

So first we calculate the current for one light: I = V/R = 115V/15Ω = 7.67 A. Being a parallel connection each light draws this same current from the power source, so for 50 light the total current I (total) drawn will be 50 * 7.67 A = 383.5 A. Therefore, the total current in the circuit is 383.5 A.

https://brainly.com/question/82566

#SPJ2

The freezing point of a substance in a cooling curve can be determined at the temperature where the substance transitions from its liquid phase to its solid phase. The freezing point may, however, be depressed in the presence of solutes. Freezing point depression is one of the colligative properties that depend on the quantity of solute particles rather than their identity.

The freezing point of a substance in a cooling curve can be determined at the point where the substance begins to transition from its liquid phase to its solid phase. The freezing point represented on the cooling curve is the temperature at which this phase transition occurs. For instance, pure water freezes at 0 °C (32 °F) under normal atmospheric pressure.

In some cases, this freezing point may vary, e.g., the freezing point of benzene is 5.5 °C. For a solution, the freezing point might be lower due to the presence of solutes; this is known as the freezing point depression. In other words, substances such as salt or sugar when mixed with water lower its freezing point, a concept used in daily life, such as making homemade ice cream or de-icing roads in winter.

For example, a solution of benzene and HCl showed a freezing point depression (ΔTf) of 5.1 °C, implying that the freezing point of the solution was lower than the pure solvent. Therefore, the freezing point of a substance can be approximated using cooling curves, considering other properties such as pressure and presence of solutes.

https://brainly.com/question/31357864

#SPJ3

A) 350 J

- The initial internal energy of the cup is

[tex]U_i = 230 J[/tex]

- The final internal energy of the cup is

[tex]U_f = 580 J[/tex]

According to the first law of thermodynamics:

[tex]U_f - U_i = Q+W[/tex]

where

Q is the heat absorbed by the system

W is the work done on the system

The work done on the system in this case is 0, so we can rewrite the equation as

[tex]U_f - U_i = Q[/tex]

And so we find the heat transferred

[tex]Q=580 J - 230 J=350 J[/tex]

B) IN the cup

Explanation:

in this situation, we see that the internal energy of the cup increases. The internal energy of an object/substance is proportional to its temperature, so it is a measure of the average kinetic energy of the molecules of the object/substance. Therefore, in this case, the temperature (and the energy of the molecules of the substance) has increased: this means that heat has been transferred INTO the system from the environment (the heat came from the sun).

Answer:

Shape of a velocity versus time graph reveals pertinent information about an object's acceleration.

Explanation:

For example, if the acceleration is zero, then the velocity-time graph is a horizontal line (the slope is zero). The gradient of a distance-time graph represents the speed of an object. The velocity of an object is its speed in a particular direction. The slope on a velocity-time graph represents the acceleration of an object. The distance travelled is equal to the area under a velocity-time graph.

The curve of a velocity vs time graph reveals significant information about an object's acceleration.

The acceleration of the object is shown by the graph between velocity and time. Any object's acceleration is the variation in velocity with the passage of time. On the graph, this temporal variation with regard to velocity is shown.

For instance, if the acceleration is 0, the velocity-time graph is a horizontal line. (There is no slope.) The gradient on a distance-time graph corresponds to an object's speed.

The velocity of an object is its speed in a certain direction. The slope of a velocity-time graph represents an object's acceleration. The distance traveled is displayed on the underside of a velocity-time graph.

Therefore, a velocity versus time graph's shape provides important details about an object's acceleration.

To know more about the time velocity graph follow

https://brainly.com/question/5285428

#SPJ2

Answer:

B

Explanation:

This option is exactly the same as the example. Thus it would require the same amount of heat.

Answer:

B) A 3-kg mass experiences a temperature rise of 50°C.

Explanation:

As we know that the rise in temperature for 3 kg object is 50 degree C then the heat added is given as 1000 J

so here we can say that formula of heat is

[tex]Q = ms\Delta T[/tex]

here we will have

[tex]m = mass[/tex]

s = specific heat capacity

[tex]\Delta T [/tex] = temperature rise

so here if we make all three parameters same to make this heat energy same

so correct answer will be

B) A 3-kg mass experiences a temperature rise of 50°C.

'A' is the false one, but 'C' is also so poorly worded that it's misleading.

Answer:

To get to the moon you need to travel in a spacecraft and will take approximately 10 hours of travel.

Explanation:

Since the first spaceship to land on the moon in 1959 , several trips have been made so far.The NASA trip in 2006 opened more routes to the moon and achieved a time travel of 8 hours compared to the first one done in 1959 that was 34 hours of time travel.Currently, NASA has intiated programs that will see robots sent to the moon for research.

Hope this helps!

Are there supposed to be multiple choices for this question?

Answer: water some food ALOT of FUNNN!!! and you'll live you also need the big guy up there

^

Answer:

Step 1 - 4. Nebular cloud of gas and dust.

Step 2. - 2. Cloud collapses under the force of its own gravitational attraction; usually triggered by a supernova.

Step 3. - 6. Condensed material begins to combine and form a core center, as it warms, a  protostar is formed.

Step 4. - 3. Other gas and matter of the nebular cloud begin to rotate around the protostar, forming a flattened disk.

Step 5. - 5. Stellar core heats as it grows; nuclear fusion begins and a star is born.

Step 6. - 1. Nuclear energy runs out; death: possible supernova.

Answer:

A star is a plasma ball held together by its gravity and compressed by a nuclear fusion at some stage in its development. The closest star on Earth is called the Sun. Several other stars can be seen in the night sky, but none of them is comparable to the Sun due to their very large distances to Earth. Traditionally, stars have been grouped into different constellations.

The stars are formed mainly by the collapse of gas vapors consisting of hydrogen due to gravity. Once the star core is formed, it slowly begins to convert hydrogen to helium in the nuclear fusion. The energy generated in the process flows from the center of the star to its surface and later radiates to outer space. The star is in equilibrium because its internal radiation pressure prevents gravity from collapsing further. When a star's hydrogen fuel is exhausted, its final fate depends on its mass: the smallest stars slowly fade away, while the more massive ones expand into red giants. Eventually, the red giants explode as a supernova, spreading various elements into space. Depending on the mass of the exploded star, for example, the remnant of an explosion may remain a neutron star or a black hole.  

By observing the motion, luminosity, and spectra of a star, it is possible to determine its other properties such as mass, age, and metal content. There are several different types of stars. The most common tool for classifying them is the Hertzsprung-Russell diagram.

Gravitationally bound star systems of two or more stars are quite common. On a large scale, stars are an important part of galaxy structure, together with interstellar gas and dark matter.