By reducing friction
Explanation:
A big machine is composed of several moving and stationary parts. Some of these parts are in a state of constant motion hence they periodically rub against each other. The friction between the body parts causes the body part to wear out and heat up in the process. This heat is symbolic of waste of energy.
The lubricating agents are a saviour in such conditions. Lubricating oils with high viscosities reduces friction. If we go deep into the working of the lubrication we find that the interacting parts of machines are quite rough when viewed under microscope. These rough surfaces when interact produce bumpy motion, wear and tear, heat etc.
Oil fills these microscopic voids and thus provides temporary relief. When these lubricated body parts interact, they encounter plain surface with decreased friction (due to high viscosity of the oils) and thus glide over each other freely thereby producing smooth movements, noiseless working.
suppose an electrically charged ruler transfers some of its charge by contact to a tiny plastic sphere. will the ruler and the sphere attract or repel afterwards? explain your reasoning
The ruler and sphere, after the charge transfer, will acquire the same type of charge. As a result, they will repel each other as like charges repel in Electrostatics.
Explanation:In the field of Physics, the force between two electrically charged objects can be either attraction or repulsion. However, in this case where an electrically charged ruler transfers some of its charge by contact to a tiny plastic sphere, the two objects will repel each other. This phenomenon is based on the fundamental principle that like charges repel each other. After the transfer of charge, both the ruler and the sphere acquire the same kind of charge, hence they repel. This concept is a foundational part of the study of Electrostatics.
Learn more about Electrostatics here:https://brainly.com/question/33600060
#SPJ3
The ruler and the sphere will repel each other after charge transfer because they will have the same type of charge, leading to a repulsive force in accordance with the principles of electrostatics and Coulomb's law.
When an electrically charged ruler transfers some of its charge to a tiny plastic sphere by contact, both objects will have the same type of charge, either positive or negative, depending on the ruler's initial charge.
According to the principle of electrostatics, like charges repel each other, meaning that the ruler and the sphere will repel each other after the charge transfer. This can be understood by considering that charges distributed on both objects are of the same sign, leading to a repulsive force between them.
For example, if a plastic ruler is rubbed with a cloth and acquires a negative charge (excess electrons), upon touching a neutral plastic sphere, some of these excess electrons will move to the sphere. This will leave both the ruler and sphere negatively charged, resulting in repulsion due to the interaction of like charges.
This is in accordance with Coulomb's law, which states that the electric force between two point charges is directly proportional to the product of the magnitude of the charges and inversely proportional to the square of the distance between the charges, and that like charges exert a repulsive force on each other.
A block on an inclined plane experiences a force due to gravity of 300 N straight down. If the slope is inclined at 67. 8° to the horizontal;
(a) what is the component of the force due to gravity perpendicular and parallel to the slope? and
(b) at what angle would the perpendicular and parallel components of the force due to gravity be equal?
Answer:
Correct answer: (a) F|| = 277.8 N and F⊥ = 113.4 N (b) α = 45°
Explanation:
Given :
Fg = 300 N and angle α = 67.8°
Let be perpendicular component be F⊥ and parallel component F||
(a)
F|| = Fg · sinα = 300 · sin 67.8° = 300 · 0.926 = 277.8 N
F|| = 277.8 N
F⊥ = Fg · cosα = 300 · cos 67.8° = 300 · 0.378 = 113.4 N
F⊥ = 113.4 N
(b)
Perpendicular and parallel components will be equal at angle
α = 45°
F⊥ = F|| = Fg · sinα = Fg · cosα = 300 · √2/2 = 212.13 N
God is with you!!!
Final answer:
When an object rests on an inclined plane, the force of gravity is divided into two components: one perpendicular to the slope and one parallel to the slope. The perpendicular component can be found using the formula w₁ = w * sin(θ), where w is the force due to gravity and θ is the angle of inclination. The parallel component can be found using the formula w|| = w * cos(θ). The perpendicular and parallel components of the force due to gravity will be equal when the object is on an incline with an angle of 45° to the horizontal.
Explanation:
When an object rests on an inclined plane that makes an angle with the horizontal, the force of gravity acting on the object can be divided into two components: a component perpendicular to the slope and a component parallel to the slope. The component perpendicular to the slope is equal in magnitude and opposite in direction to the normal force exerted by the inclined plane on the object. The component parallel to the slope causes the object to accelerate down the incline. In this case, the force due to gravity is 300 N straight down. To find the components of this force, we can use trigonometry.
(a) Perpendicular and Parallel Components
To find the component of the force due to gravity perpendicular to the slope, we can use the formula: w₁ = w * sin(θ) where w is the magnitude of the force due to gravity and θ is the angle of inclination. Substituting the values, we have: w₁ = 300 N * sin(67.8°) = 274.16 N So, the component of the force due to gravity perpendicular to the slope is approximately 274.16 N.
To find the component of the force due to gravity parallel to the slope, we can use the formula: w|| = w * cos(θ) Substituting the values, we have: w|| = 300 N * cos(67.8°) = 125.85 N So, the component of the force due to gravity parallel to the slope is approximately 125.85 N.
(b) Equal Components of Force
The perpendicular and parallel components of the force due to gravity will be equal when the object is on an incline with an angle of 45° to the horizontal. At this angle, the sine and cosine functions will have the same value, resulting in equal components of force.
Of the following telescopes, which one would best be able to pierce through the Earth's atmosphere and function on the surface of the Earth?
Answer:
D
Explanation:
The Earth's atmosphere interferes with radio waves less than any other wavelength, so the best kind of telescope to build on the Earth's surface would be a radio telescope. Although visible light telescopes are often built on Earth, they are usually put as high up as possible, such as on mountaintops, where there is less atmosphere to get in their way. Radio telescopes are usually put as far down as possible, such as in valleys, to block out human-generated radio signals coming from other parts of the surface of the Earth.
The telescope that would best be able to pierce through the Earth's atmosphere and function on the surface of the Earth is radio telescope. The correct option is A.
What is radio telescope?Radio telescopes detect and amplify radio waves from space, converting them into signals that astronomers can use to learn more about the Universe.
Because the Earth's atmosphere interferes with radio waves less than with other wavelengths, a radio telescope would be the best type of telescope to build on the Earth's surface.
Although visible light telescopes are frequently built on Earth, they are typically placed as high up as possible, such as on mountaintops, where there is less atmospheric interference.
Radio telescopes are typically placed as low as possible, such as in valleys, to block out human-generated radio signals from other parts of the Earth's surface.
Thus, the correct option is A.
For more details regarding telescope, visit:
https://brainly.com/question/556195
#SPJ2
Your question seems incomplete, the missing options are:
A. an x-ray telescope
B. an infrared telescope
C. a radio telescope
D. a visible-light telescope
The Richter scale measures the __ of an earthquake.
Answer: magnitude
Explanation: I just did it
The Richter scale measures the magnitude of an earthquake. The correct option is A.
The Richter scale is a logarithmic scale for measuring earthquake magnitude, which is a quantitative estimate of the amount of energy generated during an earthquake.
The Richter scale, developed by Charles F. Richter in 1935, provides a numerical value to earthquakes based on the amplitude of seismic waves measured by seismographs.
The Richter scale is logarithmic, which means that each whole number rise reflects a tenfold increase in ground motion amplitude and about 31.6 times greater energy release.
As a result, a higher Richter scale value signifies a more violent and damaging earthquake with greater potential for damage and devastation.
Thus, the correct option is A.
For more details regarding Richter scale, visit:
https://brainly.com/question/14028329
#SPJ2
Your question seems incomplete, the probable complete question is:
The Richter scale measures the __ of an earthquake.
A. Magnitude.
B. Density.
C. Direction.
D. type.
the highest directly measured frequency is 5.20 x 10^14 Hz, corresponding to one of the transitions in iodine-127. How many wavelengths of electromagnetic waves with this frequency could fit across a dot on a book page? Assume the dot is 2.00 x 10^-4m in diameter.
λ = 5.7 X 10⁻⁷m
On using quantum dot, it is 351
Explanation:
Given-
Frequency, f = 5.20 x 10^14 Hz
Speed of light, c = 3 X 10⁸ m/s
Wavelength, λ = ?
We know,
λ f = c
λ = c / f
λ = [tex]\frac{3 X 10^8}{5.2 X 10^1^4}[/tex]
λ = 5.7 X 10⁻⁷m
Dot = 2 X 10⁻⁴
So,
2 X 10⁻⁴ / 5.7 X 10⁻⁷m = 351
What is the ability to complete extended periods of physical activity?
Which occurrence would lead you to conclude that lights are connected in a
parallel circuit?
O
A. When one bulb burns out, a small section of lights goes out.
O
B. When one bulb burns out, all the other lights stay lit.
O
C. When one bulb burns out, a circuit breaker is tripped.
O
D. When one bulb burns out, all the lights go out.
Answer:
B
Explanation:
When one bulb burns out, all the other lights stay lit.In a parallel circuit, each component is connected to the power source directly.
A plan has a mass of 2000kg and is traveling 100 meters above the ground. What is the planes potential Energy
Answer:
2000000j
Explanation:
m*g*h
2000*100*10
=2000000
A ray in diamond (n = 2.42) has a critical angle of 41.7 deg when trying to enter benzene. What is the index of refraction in benzene?
Answer: 1.50
Explanation:
Given that:
C (critical angle) = 41.7°
n (index of refraction in benzene) = 2.42
n (index of refraction in benzene) = ?
To get the index of refraction in benzene, Apply the formula n = 1/sineC,
n = 1/sine41.7°
n = 1/sine 41.7°
n = (1/0.6652)
n = 1.50
Thus, the index of refraction for the ray in benzene is 1.50
Answer:
1.61 is the answer
Explanation:
Good luck Acellus users, please rate 5 stars!
Which of the following is not a necessary condition for seeing a magnified image with a
lens?
A. The object and image are on the same side of the lens
B. The lens must be converging
C. The observer must be placed within the focal length
D. The object must be placed within the focal length of the lens
The option stating that the observer must be placed within the focal length is false or not a necessary condition for magnification.
Explanation:
Lens are used for magnification provided the nature of the lens is known and by positioning the object at correct position. So the object should be placed in the focal point of the lens for perfect magnification, it can also be kept within the focal point or focal length. But the object should not be kept beyond the focal length of the lens.
So among the given options, the object and image should be on the same side of the lens for magnification is true. Then the nature of lens should be converging for magnification is also true. And the most important point that the object should be placed within the focal length of the lens is the most mandatory for obtaining magnification. So the option stating that the observer must be placed within the focal length is false or not a necessary condition for magnification.
Which forms of energy are involved when you turn on a desk lamp and the bulb becomes hot?
Answer:
Electric energy moves through the wire to the lamp's bulb. In the bulb's filament, electric energy transforms into thermal energy and light energy.
Explanation:
Wind blowing sand from one location to another is an example of
erosion
movement
weathering
deposition
Wind blowing sand from one location to another is an example of erosion. Sand being blown by the wind from one place to another is an actual instance of erosion.
When the wind's force moves and displaces loose sand or other sediment particles, the process is known as wind erosion. Sand particles are picked up and carried by the wind as it sweeps across an open surface, where they impact with other items or surfaces.
Rocks, dunes, cliffs, and other geological structures can all be eroded over time as a result of the continuous movement and influence of wind-blown sand on the environment. Deserts and sandy ecosystems are mostly shaped by wind erosion on a global scale.
To know more about erosion :
https://brainly.com/question/30587260
#SPJ5.
how does friction affect the motion of an object
Answer:
#See solution for details.
Explanation:
-Friction is the force exerted on an object moving against it.
-Friction acts in the opposite direction to the object's motion.
-As such, friction reduces the motion of an object. The object is usually slowed down. The resultant motion of the object is less than the force applied on it.
what has to happen for a feather and ball to fall at the same time
Which subatomic particle has a negative charge? A) electron B) neutron C) nucleus D) proton
Answer:
A) electron
Explanation:
Matter consists of atoms. Each atom consists of three particles:
- The proton: the protons are located inside the nucleus of the atom. They have a mass of [tex]1.67\cdot 10^{-27}kg[/tex], and they have positive electric charge ([tex]+e=+1.6\cdot 10^{-19}C[/tex]). Protons are not fundamental particles, but they actually consists of three quarks (which are instead fundamental particles), in particular of 2 up quarks and 1 down quark.
- The neutron: neutrons are also located inside the nucleus. They have no electric charge, and their mass is similar to that of the proton (slightly larger). Neutrons consist of three quarks as well, in particular of 2 down quarks and 1 up quark.
- The electron: electrons are located outside the nucleus. They have a mass much smaller than protons (about [tex]9.11\cdot 10^{-31} kg[/tex]) and they have a negative electric charge, opposite to that of the proton ([tex]-e=-1.6\cdot 10^{-19}C[/tex]). The electron is a fundamental particle.
Therefore, the subatomic particle having a negative charge is
A) electron
An electron is the subatomic particle that has a negative charge. Electrons orbit the nucleus, which contains the protons and neutrons, and its negative charge helps to balance the positive charge of the protons.
Explanation:
The subatomic particle that has a negative charge is the electron. Subatomic particles, namely protons, neutrons, and electrons, make up atoms. Protons carry a positive charge and are found in the nucleus of the atom. Neutrons are neutral as they do not carry any charge and are also found in the nucleus. Electrons, which carry a negative charge, move in spaces around the nucleus known as energy levels or electron shells. The negative charge of the electron balances the positive charge of the protons, causing an atom to be neutral under normal conditions.
Learn more about Electron here:https://brainly.com/question/34085707
#SPJ3
Acetylene gas (C2H2) is used in welding torches. When it reacts with oxygen, it produces carbon dioxide (CO2) and steam (H2O). The reaction can be described by the equation:
2C2H2 + 5O2 ➔ 4CO2 + 2H2O. How much mass of C2H2 is needed to react with 68.1 g of O2 to produce 75.0 g of CO2 and 15.35 g of steam?
Explanation:
First thing to understand is how you can manipulate the Ideal Gas Law to your needs. since [tex]\mathrm{PV}=\mathrm{nRT}[/tex] at a constant temperature, [tex]\mathrm{PV} / \mathrm{n}=\mathrm{RT}=[/tex]constant. That means,
[tex]\mathrm{P}_{1} \mathrm{V}_{1} / \mathrm{n} 1=\mathrm{P} 2 \mathrm{V} 2 / \mathrm{n} 21[/tex]
If we say that subscript 1= oxygen and subscript 2= acetylene, then for acetylene,[tex]P 2=(P I V 1 \cap 2) /(\sqrt{2} n 1)[/tex]
Next, we realize from the reaction equation given above that 2 moles of acetylene (n 2 ) react with 5 moles of oxygen (n1). We can plug that right into our equation for P 2, along with the rest of the conditions given in the question:
[tex]P 2=(P 1 V 1 \cap 2) /(V 2 n 1)=\left[(155 a t m)^{*}(5.00 L)^{*}(2 m o l e s)\right] /\left[(25.00 L)^{*}(5 \text { moles }]\right]=124 \text { atm }[/tex]
Answer:
22.13g of C2H2
Explanation:
Step 1:
The balanced equation for the reaction. This is given below:
2C2H2 + 5O2 ➔ 4CO2 + 2H2O
Step 2:
Determination of masses of C2H2 and O2 that reacted from the balanced equation. We need to obtain the mass of C2H2 and that of O2 that reacted based on the chemical equation, as it will enhance the process of obtaining the desired result. This is illustrated below:
2C2H2 + 5O2 ➔ 4CO2 + 2H2O
Molar Mass of C2H2 = (12x2) + (2x1) = 24 + 2 = 26g/mol
Mass of C2H2 from the balanced equation = 2 x 26 = 52g
Molar Mass of O2 = 16x2 = 32g/mol
Mass of O2 from the balanced equation = 5 x 32 = 160g
From the balanced equation,
52g of C2H2 reacted with 160g of O2.
Step 3:
Determination of the mass of C2H2 needed to react with 68.1g of O2.
From the balanced equation,
52g of C2H2 reacted with 160g of O2
Therefore, Xg of C2H2 will react with 68.1g of O2 i.e
Xg of C2H2 = (52 x 68.1)/160
Xg of C2H2 = 22.13g
From the calculations made above, 22.13g of C2H2 is needed to react with 68.1 g of O2 to produce 75.0 g of CO2 and 15.35 g of steam
A box sliding down a hill going 3m/s accelerates at 2m/s2. How fast is going 4 seconds?
Final answer:
The box sliding down the hill with an initial velocity of 3 m/s and accelerating at 2 m/s² will be going 11 m/s after 4 seconds.
Explanation:
The question involves a box sliding down a hill with an initial velocity of 3 m/s, which then accelerates at 2 m/s². To find out how fast the box will be going after 4 seconds, we apply the kinematic equation:
v = u + at,
where v is the final velocity, u is the initial velocity, a is the acceleration, and t is the time. Plugging in the values, we get:
v = 3 m/s + (2 m/s² * 4 s) = 3 m/s + 8 m/s = 11 m/s.
The box will be going 11 m/s after 4 seconds.
Which of these can be considered a system? Check all that apply.
O a computer
O a car
O a bicycle pedal
O a pencil
O a coffeemaker
Answer: A b e
Explanation:
Systems are a computer, a car, and a coffeemaker. Therefore, options A, B, and D are correct.
A system refers to a well-defined portion of the physical universe that is the subject of study or analysis. It is a fundamental concept used to simplify and focus investigations into the behavior and interactions of objects or components within a specific region of interest.
A physics system can consist of one or more physical objects, particles, or components that are the primary subjects of study. These components are chosen based on the specific physics principles or phenomena being investigated. Therefore, options A, B, and D are correct.
Learn more about systems, here:
https://brainly.com/question/3602141
#SPJ3
20 POINTS!!!!!!!!
An electromagnet is a temporary magnet made by coiling wire around an iron core which becomes a magnet when an electric current flows through the wire.
How could the strength of an electromagnet be increased?
A) Use fewer coils of wire around the nail.
B) Use more coils of wire around the nail.
C) Use a battery with less voltage.
D) Use a smaller nail.
USE MORE COILS OF WIRE AROUND THE NAIL
Explanation:
To increase the strength of an electromagnet, the following strategy is adopted in order to have better efficiency.
The best method which suits for increasing the strength of electromagnet is to increase the number of turns around the nail.
If we increase the number of turns up to a specific value the magnetizing property of magnet is enhanced. So that to increase the strength , add more number of turns to the existing turns of coil.
A book has a mass of 50 grams and an
acceleration of 5 m/s/s. What is the force on
the book?
220 N
20 N
250 N
10 N
The force on the book that has a mass of 50 grams and an acceleration of 5 m/s² is 250N.
How to calculate force?The force of an object can be calculated by multiplying the mass by its acceleration as follows:
Force = mass × acceleration
According to this question, a book has a mass of 50 grams and an acceleration of 5 m/s². The force is as follows:
Force = 50 × 5
Force = 250N
Therefore, the force on the book that has a mass of 50 grams and an acceleration of 5 m/s² is 250N.
Learn more about force at: https://brainly.com/question/13191643
The correct force on the book is 2.5 N.
To find the force on the book, we can use Newton's second law of motion, which states that force is equal to mass times acceleration (F = m × a).
Given:
- The mass of the book (m) is 50 grams. To convert grams to kilograms (since the standard unit of mass in the SI system is kilograms), we divide by 1000. Thus, m = 50 / 1000 kg = 0.05 kg.
- The acceleration (a) of the book is 5 m/s².
Using Newton's second law, we calculate the force (F) as follows:
F = m × a
F = 0.05 kg × 5 m/s²
F = 0.25 kg × m/s²
Since 1 Newton is equal to 1 kgm/s², the force on the book is 0.25 Newtons, or 2.5 N.
Therefore, the correct answer is 2.5 N, which is not listed in the given options. It seems there was a typo in the provided options, as the correct calculation does not result in any of the listed forces. The closest option to the correct answer is 20 N, but it is still incorrect. The correct force is 2.5 N.
A current of 1.41 A in a long, straight wire produces a magnetic field of 5.61 uT at a certain distance from the wire. Find
this distance.
Answer:
0.050 m
Explanation:
The strength of the magnetic field produced by a current-carrying wire is given by
[tex]B=\frac{\mu_0 I}{2\pi r}[/tex]
where
[tex]\mu_0=4\pi \cdot 10^{-7} H/m[/tex] is the vacuum permeability
I is the current in the wire
r is the distance from the wire
And the magnetic field around the wire forms concentric circles, and it is tangential to the circles.
In this problem, we have:
[tex]I=1.41 A[/tex] (current in the wire)
[tex]B=5.61\mu T=5.61\cdot 10^{-6} T[/tex] (strength of magnetic field)
Solving for r, we find the distance from the wire:
[tex]r=\frac{\mu_0 I}{2\pi B}=\frac{(4\pi \cdot 10^{-7})(1.41)}{2\pi (5.61\cdot 10^{-6})}=0.050 m[/tex]
describe the relationship between the direction of the velocity vector and the direction of the acceleration for a body moving in a circle at constant speed
The direction of the velocity vector in circular motion at constant speed is tangent to the circle, while the acceleration vector, known as centripetal acceleration, points toward the center of the circle.
Explanation:In the specific scenario of a body moving in a circle at a constant speed, the relationship between the direction of the velocity vector and the direction of the acceleration vector is vital to understand. The velocity vector is always tangent to the circle, which means it is drawn along the direction that the body is moving at any point on the circle. The acceleration vector, on the other hand, points toward the center of the circle; this is known as centripetal acceleration. Thus, while the speed remains constant, the direction of the velocity is continuously changing as the body moves along the circular path, resulting in an acceleration towards the center of that path.
Label the parts of the transverse wave.
Amplitude:
Crest :
Trough:
Wavelength:
Answer:
Amplitude: B
Crest: A
Trough: C:
Wavelength: D
Explanation:
The amplitude of the wave is defined as the distance from the equilibrium position of the wave to its crest or troughs; therefore,
Amplitude: B
The Crest of a wave is its highest point from its equilibrium position; therefore,
Crest: A
The trough of a wave is its lowest point measured from equilibrium position; therefore,
Trough: C
The wavelength of a wave is the distance between two identical points on a wave; therefore,
Wavelength: D.
The parts of a transverse wave are the amplitude, crest, trough, and wavelength.
Explanation:Amplitude: The amplitude of a transverse wave is the maximum displacement of a point on the wave from its equilibrium position. It represents the intensity or strength of the wave. For example, in a water wave, the amplitude would be the height of the wave from the water's surface.
Crest: The crest of a transverse wave is the highest point of the wave above the equilibrium position. It is the point where the displacement is maximum in the upward direction.
Trough: The trough of a transverse wave is the lowest point of the wave below the equilibrium position. It is the point where the displacement is maximum in the downward direction.
Wavelength: The wavelength of a transverse wave is the distance between two consecutive crests or troughs of the wave. It is usually represented by the symbol λ (lambda) and is measured in meters. It determines the spatial extent of the wave.
Learn more about Transverse wave here:https://brainly.com/question/23165088
#SPJ12
a swing has a period of 3 seconds. what is it’s frequency?
f = 1/3 swings per second
or
f = 1 swing per 3 seconds
The frequency of a swing with a period of 3 seconds is approximately 0.33 Hz, calculated using the relationship f = 1/T.
The question is asking us to calculate the frequency of a swing given its period. The known period of the swing is 3 seconds. To find the frequency, which is the number of cycles the swing completes in one second, we can use the relationship between period (T) and frequency (f), which is f = 1/T. Thus, for a period of 3 seconds, the frequency is simply f = 1/3 seconds = 0.333... cycles per second, or approximately 0.33 Hz when rounded to two decimal places.
an astronaut weighs 199 lb. what is his weight in newtons?
1 lb = 4.45 Newtons (rounded)
199 lbs = approx 885 Newtons
You lift a large bag of flour from the floor to a 2.5m high counter, doing 400J of work in 2 seconds. How much force did you apply?
Explanation:
The work done to lift the bag of weight mg through height 2.5 m is 400 J
The work done can be found by relation W = mg x h
Thus mg = [tex]\frac{W}{h}[/tex] = [tex]\frac{400}{2.5}[/tex] = 160 N
Therefore the man have to apply the force of 160 N
Answer:160newtons
Explanation:
Work=400J
Distance=2.5m
Time=2 seconds
Force=?
Force=work/distance
Force=400/2.5
Force=160
Force=160 newtons
Which of the following best describes what occurs in a fusion reaction?
Answer:
In the process some of the mass of the hydrogen is converted into energy. ... The sun and stars do this by gravity.
Explanation:
A boy ties a stone to the end of a string which he then whirles above his head round a circular path of radius 15cm. if the stone makes 20 oscillations in 10 seconds calculate the angular and linear speeds of the stone.
Answer:
W = 12.568rads
V = 1.8852m/s
Explanation:
Data:
r = 15cm = 0.15m
t = 10s
Revolutions = 20
Frequency (F) = number revolutions/ time take complete it
F = 20 / 10 = 2Hz
Angular velocity (w) = 2 * 3.142 * F
Note: 3.142 = value of pi
W = 2*3.142*2 = 12.568 rads
Linear velocity (v) = w*r
V = 12.568*0.15 = 1.8852m/s
8. Grass uses energy from the Sun
to grow. A cow eats grass so it
has energy to walk. You drink
milk from the cow so you have
energy to hit a ball. This makes
a loud sound and sends the ball
flying. In these steps, energy
keeps moving and changing.
What is this series of steps called?
® energy movement
® energy switching
© energy transfer
O energy conversion
Answer:
The correct option is D) energy conversion
Explanation:
As we all know, energy is neither created nor destroyed but is can be converted from one form to another.
For example, the chemical energy in food is converted into kinetic energy when we run or walk.
The changing of the energy is called energy conversion and the movement of the energy is called energy transfer.
is is false or true The closer objects are, the stronger the gravitational force between them.
Answer:
TRUE
Explanation:
The gravitational force between two objects becomes weaker if the two objects are moved apart and stronger if they are brought closer together; that is, the force depends on the distance between the objects