Answer:
2354.4 Pa
40221 Pa
Explanation:
[tex]\rho[/tex] = Density = 1000 kg/m³
g = Acceleration due to gravity = 9.81 m/s²
h = Depth
The pressure difference would be
[tex]\Delta P=\rho gh\\\Rightarrow \Delta P=1000\times 0.24\times 9.81\\\Rightarrow \Delta P=2354.4\ Pa[/tex]
The pressure difference in the first case is 2354.4 Pa
[tex]\Delta P=\rho gh\\\Rightarrow \Delta P=1000\times 4.1\times 9.81\\\Rightarrow \Delta P=40221\ Pa[/tex]
The pressure difference in the second case is 40221 Pa
A 539 g ball strikes a wall at 14.4 m/s and
rebounds at 13.8 m/s. The ball is in contact
with the wall for 0.033 s.
What is the magnitude of the average force
acting on the ball during the collision?
Answer in units of N.
Answer:
461 N
Explanation:
Impulse = change in momentum
F Δt = m Δv
F (0.033 s) = (0.539 kg) (14.4 m/s − (-13.8 m/s))
F = 461 N
A beam of electrons, each with the same kinetic energy, illuminates a pair of slits separated by a distance of 51 nm. The beam forms bright and dark fringes on a screen located a distance 2.6 m beyond the two slits. The arrangement is otherwise identical to that used in the optical two-slit interference experiment. The bright fringes are found to be separated by a distance of 0.4 mm. What is the kinetic energy of the electrons in the beam? Planck’s constant is 6.63 × 10−34 J · s. Answer in units of keV.
Answer:
K = 24.5 keV
Explanation:
The interference phenomenon is described by the equation
.d sin θ = m λ m = 1,2,3,…
The pattern is observed on a screen at a distance L = 2.6 m
tan θ = y / L
As these experiments the angle is very small we can approximate the tangent
tan θ = sin θ / cos θ
For small angles
tan θ = sin θ
Let's replace
d y / L = m λ
λ = d y / m L
Let's reduce the units to the SI system
d = 51 nm = 51 10⁻⁹ m
y = 0.4 mm = 0.4 10⁻³ m
Let's calculate the wavelength
Let's use m = 1 for the first interference line
λ = 51 10⁻⁹ 0.4 10⁻³ / 2.6
λ = 7.846 10⁻¹² m
Let's look for kinetic energy
K = ½ m v²
p = mv
K = ½ m p² / m
K = p² / 2m
Let's use the wave-particle duality relationship
p = h /λ
K = h² / 2m λ²
Let's calculate
K = (6.63 10⁻³⁴)² / (2 9.1 10⁻³¹ (7.846 10⁻¹²)²)
K = 3,923 10⁻¹⁵-15 J
K = 3.923 10⁻¹⁵ J ( 1 eV / 1.6 10⁻¹⁹ J) =2.452 10⁴ eV
K = 24.5 keV
If you drink cold water, it will soon warm up to body temperature (about 37 C) This takes energy. Therefore, you ought to be able to keep your weight down even if you eat fattening food provided you also drink lots of cold water, right?Estimate what volume of cold water you would need to drink to overcome the effect of eating one chocolate sundae. (A chocolate sundae contains about 500 Cal. Recall that 1 Cal, the "calorie" normally used in the US to measure the energy content of food, is 1000 cal, or 1kcal.)
Answer:
18.4 L
Explanation:
A chocolate sundae contains 500 Cal. Considering that 1 Cal = 1 kcal and 1 kcal = 4.184 kJ, a chocolate sundae contains:
500 Cal × (4.184 kJ / 1 Cal) = 2.09 × 10³ kJ
Let's suppose we drink water at 10°C that increases its temperature to 37°C by absorbing this heat (Q). We can find the mass of water using the following expression.
Q = c × m × ΔT
where,
c: specific heat capacity of the water
m: mass
ΔT: change in the temperature
Q = c × m × ΔT
2.09 × 10³ kJ = (4.19 kJ/kg.°C) × m × (37°C - 10°C)
m = 18.4 kg
Considering the density of water to be of 1 kg/L, the volume of water is 18.4L.
Final answer:
To counteract the 500 kcal from a chocolate sundae, you would need to drink approximately 14.3 liters of ice-cold water. However, this is neither practical nor safe, and weight management should involve a balance of diet and exercise instead.
Explanation:
Drinking cold water does indeed require energy from the body to warm it up to body temperature, thus expending calories in the process.
To estimate the volume of cold water needed to negate the caloric intake of one chocolate sundae, we can use the given information that 250 mL of ice-cold water takes approximately 8,750 calories (or 8.75 kcal) to be heated up to body temperature.
If a chocolate sundae contains about 500 Cal (500 kcal), we would need to drink a significantly larger volume of cold water to burn those calories. Specifically, we can calculate this using a simple ratio:
500 kcal (chocolate sundae) / 8.75 kcal (250 mL water) = x / 250 mL
This gives us:
x = 250 mL × (500/8.75)
x = 14,285.71 mL
So, you would need to drink approximately 14.3 liters of ice-cold water to counteract the caloric intake from one chocolate sundae, which is not practical or safe.
What mathematical evidence can you provide to support the assertion that the universe is electrically neutral on large scales?Ryden, Barbara. Introduction to Cosmology (p. 47). Cambridge University Press. Kindle Edition.
It is likely that until today there is no physical / mathematical argument that allows to equate this statement. But there are countless observations that have led to that conclusion.
From these observations two types of highlights can be summarized: Magnetic fields and Gravity Force.
Electromagnetic Field: If there is a negative or positive charge, these charges should be observed through the electric and magnetic fields by means of microwaves. However, there is currently no observation that supports any electromagnetic charge in space.
Force of gravity: The only force capable of maintaining the attraction of the planets, without affecting (at certain scales), is the force of gravity. An electromagnetic force often exceeds that of gravity, but has not been observed at the moment.
Final answer:
Mathematical and observational evidence from electromagnetism and cosmology, such as the Maxwell-Einstein theoretical framework and charge quantization, supports the assertion that the universe is electrically neutral on large scales.
Explanation:
To support the assertion that the universe is electrically neutral on large scales, one can turn to the principles of electromagnetism and cosmology melded in the framework of the general theory of relativity. A key aspect of this inquiry relates to the near uniform distribution of matter and the overall balance of positive and negative charges in the cosmos.
On quantum scales, charge quantization ensures that matter is made up of atoms with equal numbers of protons and electrons, contributing to the electrical neutrality on a smaller scale. This neutrality scales up to larger structures in the universe. Observational evidence also points towards the large-scale neutrality of the universe; otherwise, we would observe huge electrostatic forces that would significantly alter the structure of the cosmos.
The mean distance of an asteroid from the Sun is 2.98 times that of Earth from the Sun. From Kepler's law of periods, calculate the number of years required for the asteroid to make one revolution around the Sun. Number Enter your answer in accordance to the question statement Entry field with incorrect answer Units Choose the answer from the menu in accordance to the question statement Entry field with correct answer.
Answer:
The asteroid requires 5.14 years to make one revolution around the Sun.
Explanation:
Kepler's third law establishes that the square of the period of a planet will be proportional to the cube of the semi-major axis of its orbit:
[tex]T^{2} = a^{3}[/tex] (1)
Where T is the period of revolution and a is the semi-major axis.
In the other hand, the distance between the Earth and the Sun has a value of [tex]1.50x10^{8} Km[/tex]. That value can be known as well as an astronomical unit (1AU).
But 1 year is equivalent to 1 AU according with Kepler's third law, since 1 year is the orbital period of the Earth.
For the special case of the asteroid the distance will be:
[tex]a = 2.98(1.50x10^{8}Km)[/tex]
[tex]a = 4.47x10^{8}Km[/tex]
That distance will be expressed in terms of astronomical units:
[tex]4.47x10^{8}Km.\frac{1AU}{1.50x10^{8}Km}[/tex] ⇒ [tex]2.98AU[/tex]
Finally, from equation 1 the period T can be isolated:
[tex]T = \sqrt{a^{3}}[/tex]
[tex]T = \sqrt{(2.98)^{3}}[/tex]
[tex]T = \sqrt{26.463592}[/tex]
[tex]T = 5.14AU[/tex]
Then, the period can be expressed in years:
[tex]5.14AU.\frac{1yr}{1AU} ⇒ 5.14 yr[/tex]
[tex]T = 5.14 yr[/tex]
Hence, the asteroid requires 5.14 years to make one revolution around the Sun.
Final answer:
Using Kepler's third law, the asteroid that is 2.98 times the mean distance of Earth from the Sun has an orbital period of approximately 5.14 years.
Explanation:
To calculate the orbital period of an asteroid using Kepler's third law of planetary motion, which relates the orbital period of a planet to its average distance from the Sun, we first need to understand that the asteroid's mean distance from the Sun is given as 2.98 times the Earth's mean distance from the Sun.
Since 1 astronomical unit (AU) is the mean distance of Earth from the Sun, we'll denote the asteroid's mean distance as 2.98 AU. Kepler's third law can be formulated as P² = a³, where P is the orbital period in Earth years, and a is the semimajor axis or mean distance from the Sun in astronomical units.
To find the period P, we take the cube of the mean distance (2.98³) and then take the square root of that number to find the orbital period in years.
Calculation:
a = 2.98 AU (mean distance to the Sun)
a³ = 2.98 x 2.98 x 2.98 = 26.45
P² = 26.45
P = √26.45
P ≈ 5.14 years
Therefore, the asteroid takes approximately 5.14 years to make one revolution around the Sun.
A horizontal beam of unpolarized light is incident on a stack of three polarizing filters with their polarization axes oriented, in sequence, 30◦, 60◦ and 90◦ clockwise from the vertical. The intensity of the light emerging from the stack is measured to be 275 W/m2. What is the intensity of the emerging light (in W/m2) if the middle polarizing filter is removed?
Answer:
122.22 W/m²
Explanation:
Let the intensity of unpolarized light is Io.
from first polariser
I' = Io/2
From second polariser
I'' = I' Cos²30 = 3 Io/8
From third polariser
I''' = I'' Cos²30 = 9Io/32
According to the question
9Io/32 = 275
Io = 977.78 watt/m²
Now, from first polariser
I' = Io/2 = 977.78 / 2 = 488.89 W/m²
I'' = 488.89 x cos²60 = 122.22 W/m²
thus, the intensity of light is 122.22 W/m².
Answer:
Explanation:
Given
Intensity of light emerging out is [tex]I=275 W/m^2[/tex]
Polarizer axis are inclined at [tex]30^{\circ}] , [tex]60^{\circ}[/tex] , [tex]90^{\circ}[/tex]
If [tex]I_0[/tex] is the Intensity of Incoming light then
[tex]275=\frac{I_0}{2}\times \cos ^2{30}\times \cos^2 {30}[/tex]
as they are inclined to [tex]30^{\circ}[/tex]to each other
[tex]I_0=\frac{275}{9}\times 32[/tex]
[tex]I_0=977.77 W/m^2[/tex]
If middle Filter is removed then
[tex]I=0.5\cdot I_0\cos ^2{60}[/tex]
[tex]I=0.5\cdot 977.77\cdot \frac{1}{4}[/tex]
[tex]I=122.22 W/m^2[/tex]
As in problem 80, an 76-kg man plans to tow a 128000-kg airplane along a runway by pulling horizontally on a cable attached to it. Suppose that he instead attempts the feat by pulling the cable at an angle of 6.7° above the horizontal. The coefficient of static friction between his shoes and the runway is 0.87. What is the greatest acceleration the man can give the airplane? Assume that the airplane is on wheels that turn without any frictional resistance.
In order to solve this problem it is necessary to apply the concepts related to Newton's second law and the respective representation of the Forces in their vector components.
The horizontal component of this force is given as
F_x = Fcos(6.7)
While the vertical component of this force would be
F_y = Fsin(6.7)
In the vertical component, the sum of Force indicates that:
[tex]\sum F_y= 0 [/tex]
The Normal Force would therefore be equivalent to the weight and vertical component of the applied force, therefore:
[tex]N = mg+Fsin(6.7)[/tex]
In the horizontal component we have that the Force of tension in its horizontal component is equivalent to the Force of friction:
[tex]\sum F_x = 0[/tex]
[tex]F_x = F_{friction}[/tex]
[tex]Fcos (6.7) = N\mu[/tex]
Using the previously found expression of the Normal Force and replacing it we have to,
[tex]Fcos(6.7)= \mu (mg+Fsin(6.7))[/tex]
Replacing,
[tex]Fcos(6.7)= (0.87) (mg+Fsin(6.7))[/tex]
[tex]Fcos(6.7) = (0.87)(mg) + (0.87)(Fsin(6.7))[/tex]
[tex]Fcos(6.7) -(0.87)(Fsin(6.7)) = 0.87 (mg)[/tex]
[tex]F(cos(6.7)-0.87sin(6.7)) = 0.87 (mg)[/tex]
[tex]F = \frac{0.87 (mg)}{(cos(6.7)-0.87sin(6.7))}[/tex]
[tex]F = \frac{0.87(128000*9.8)}{(cos(6.7)-0.87sin(6.7))}[/tex]
[tex]F = 1.95*10^6N[/tex]
Finally the acceleration would be by Newton's second law:
[tex]F = ma[/tex]
[tex]a = \frac{F}{m}[/tex]
[tex]a = \frac{ 1.95*10^6}{128000}[/tex]
[tex]a = 15.234m/s^2[/tex]
Therefore the greatest acceleration the man can give the airplane is [tex]15.234m/s^2[/tex]
the greatest acceleration the man can give the airplane is approximately 7.38 m/s²
The greatest acceleration the man can give the airplane when pulling at an angle of 6.7° above the horizontal is given by the equation:
[tex]\[ a = \frac{\mu (m_m + m_a) g - m_a g \sin(\theta)}{m_m + m_a \cos(\theta)} \][/tex]
where:
- [tex]\( \mu \)[/tex] is the coefficient of static friction between the man's shoes and the runway,
- [tex]\( m_m \)[/tex] is the mass of the man,
- [tex]\( m_a \)[/tex] is the mass of the airplane,
- g is the acceleration due to gravity,
- [tex]\( \theta \)[/tex] is the angle at which the man pulls the cable.
Given:
[tex]- \( \mu = 0.87 \),[/tex]
[tex]- \( m_m = 76 \) kg,[/tex]
[tex]- \( m_a = 128000 \) kg,[/tex]
[tex]- \( g = 9.8 \) m/s²,[/tex]
[tex]- \( \theta = 6.7° \).[/tex]
First, we need to convert the angle from degrees to radians because the sine and cosine functions in trigonometry typically use radians:
[tex]\[ \theta_{\text{radians}} = \theta_{\text{degrees}} \times \frac{\pi}{180} \][/tex]
[tex]\[ \theta_{\text{radians}} = 6.7° \times \frac{\pi}{180} \][/tex]
Now, we can plug in the values into the equation:
[tex]\[ a = \frac{0.87 (76 \text{ kg} + 128000 \text{ kg}) \times 9.8 \text{ m/s}^2 - 128000 \text{ kg} \times 9.8 \text{ m/s}^2 \times \sin(6.7°)}{76 \text{ kg} + 128000 \text{ kg} \times \cos(6.7°)} \][/tex]
Calculating the sine and cosine of 6.7°:
[tex]\[ \sin(6.7)\approx 0.117 \][/tex]
[tex]\[ \cos(6.7) \approx 0.993 \][/tex]
Now, we substitute these values into the equation:
[tex]\[ a = \frac{0.87 (76 + 128000) \times 9.8 - 128000 \times 9.8 \times 0.117}{76 + 128000 \times 0.993} \][/tex]
Solving the numerator:
[tex]\[ (0.87 \times 128076 \times 9.8) - (128000 \times 9.8 \times 0.117) \][/tex]
[tex]\[ = (0.87 \times 128076 \times 9.8) - (128000 \times 1.1466) \][/tex]
[tex]\[ = 939608.16 \][/tex]
Solving the denominator:
[tex]\[ 76 + (128000 \times 0.993) \][/tex]
[tex]\[ = 127308 \][/tex]
Finally, we divide the numerator by the denominator to find the acceleration:
[tex]\[ a = \frac{939608.16}{127308} \][/tex]
[tex]\[ a \approx 7.38 \text{ m/s}^2 \][/tex]
The answer is: 7.38.
At a circus, a clown is being shot out of a cannon. This is a good thing because clowns are terrifying. The cannon's barrel makes an angle of 35 degrees with the ground and the initial velocity has magnitude 10.4 m/s. The end of the barrel is 1.0 m above the ground. A 1.0 m thick mattress, with sides 2.0 m long, is placed so its closest edge is a horizontal distance of 10.0 m from the end of the cannon's barrel. (a) Draw a diagram of the situation described. Label the x and y directions, the cannon, the mattress, the initial velocity vector and the barrel angle. (b) What are the vertical and horizontal components of the initial velocity vector? (c) At what time will the clown return to a height of 1.0 m above the ground? (d) Using your answer from (c), will the clown reach the mattress and escape serious injury??? What would you expect if we included the effects of air resistance? (disclaimer: no matter how terrifying clowns are, I still would not wish one to be seriously hurt)
Answer:
a) Please, see the attached figure.
b) The horizontal component of the initial velocity is 8.5 m/s
The vertical component of the initial velocity is 6.0 m/s
c) The clown will return to a height of 1.0 m after 1.2 s of the launch.
d) The clown will land safely on the mattress, 10.2 m from the cannon. If we include air resistance in the calculation, he will surely not reach the mattress because, without air resistance, he lands just 20 cm from the closest edge of the mattress.
Explanation:
Hi!
a) Please, see the attached figure.
b) As shown in the figure, the initial velocity vector is the following:
v0 = (v0x, v0y)
Using trigonomety of right triangles:
cos angle = adjacent side / hypotenuse
In this case:
Adjacent side = v0x
hypotenuse = v0
(see figure)
Then:
cos 35° = v0x / v0
v0 · cos 35° = v0x
v0x = 10.4 m/s · cos 35°
v0x = 8.5 m/s
The horizontal component of the initial velocity is 8.5 m/s
We proceed in the same way to find the vertical component:
sin angle = opposite side / hypotenuse
sin 35° = v0y / v0 (see figure to notice that opposite side = v0y)
v0 · sin 35° = v0y
10.4 m/s · sin 35° = v0y
v0y = 6.0 m/s
The vertical component of the initial velocity is 6.0 m/s
c) The equation of the position vector of the clown at time t is the following:
r = (x0 + v0 · t · cos α, y0 + v0 · t · sin α + 1/2 · g · t²)
Where:
x0 = initial horizontal position.
v0 = initial velocity.
t = time.
α = launching angle.
y0 = initial vertical position.
g = acceleration due to gravity (-9.8 m/s² considering the upward direction as positive).
We have to find the time at which the vertical component of the position vector is 1 m. Let´s place the origin of the system of reference at the point where the cannon is located on the ground so that x0 = 0 and y0 = 1.0 m.
Using the equation of the vertical component of the position:
y = y0 + v0 · t · sin α + 1/2 · g · t²
1.0 m = 1.0 m + 10.4 m/s · t · sin 35° - 1/2 · 9.8 m/s² · t²
0 = 10.4 m/s · t · sin 35° - 4.9 m/s² · t²
0 = t (10.4 m/s · sin 35° - 4.9 m/s² · t) (t = 0, when t = 0 the clown is 1.0 m above the ground, just leaving the cannon).
0 = 10.4 m/s · sin 35° - 4.9 m/s² · t
-10.4 m/s · sin 35° / -4.9 m/s² = t
t = 1.2 s
The clown will return to a height of 1.0 m after 1.2 s of the launch.
d) Now, let´s calculate the horizontal traveled distance after 1.2 s using the equation of the horizontal component of the position vector:
x = x0 + v0 · t · cos α (x0 = 0)
x = 10.4 m/s · 1.2 s · cos 35°
x = 10.2 m
Since the mattress is located at 10 m from the cannon and it is 2.0 m long, the clown will land safely on the mattress. However, the clown almost miss the mattress (he lands just 20 cm from the closest edge), so, if we include air resistance in the calculation, he will surely not reach the mattress.
When the displacement in SHM is equal to 1/3 of the amplitude xm, what fraction of the total energy is (a) kinetic energy and (b) potential energy? (c) At what displacement, in terms of the amplitude, is the energy of the system half kinetic energy and half potential energy? (Give the ratio of the answer to the amplitude)
Answer:
Explanation:
Given
Displacement is [tex]\frac{1}{3}[/tex] of Amplitude
i.e. [tex]x=\frac{A}{3}[/tex] , where A is maximum amplitude
Potential Energy is given by
[tex]U=\frac{1}{2}kx^2[/tex]
[tex]U=\frac{1}{2}k(\frac{A}{3})^2[/tex]
[tex]U=\frac{1}{18}kA^2[/tex]
Total Energy of SHM is given by
[tex]T.E.=\frac{1}{2}kA^2[/tex]
Total Energy=kinetic Energy+Potential Energy
[tex]K.E.=\frac{1}{2}kA^2 -\frac{1}{18}kA^2[/tex]
[tex]K.E.=\frac{8}{18}kA^2[/tex]
Potential Energy is [tex]\frac{1}{8}[/tex] th of Total Energy
Kinetic Energy is [tex]\frac{8}{9}[/tex] of Total Energy
(c)Kinetic Energy is [tex]0.5\times \frac{1}{2}kA^2[/tex]
[tex]P.E.=\frac{1}{4}kA^2[/tex]
[tex]\frac{1}{2}kx^2=\frac{1}{4}kA^2[/tex]
[tex]x=\frac{A}{\sqrt{2}}[/tex]
Answer:
Explanation:
Let the amplitude is A.
Displacement, x = one third of the amplitude = A/3
The total energy of the body executing Simple Harmonic Motion is given by
[tex]T=\frac{1}{2}KA^{2}[/tex]
(a) Kinetic energy of the particle executing SHM is given by
[tex]K=\frac{1}{2}K\left (A^{2} -x^{2} \right )[/tex]
[tex]K=\frac{1}{2}K\left (A^{2} -\frac{A}{9}^{2} \right )[/tex]
[tex]K=\frac{1}{2}\times \frac{8A^{2}}{9}[/tex]
So, the ratio of kinetic energy to the total energy is given by
K / T = 8 / 9
(b) Potential energy of a particle executing SHM is given by
[tex]U=\frac{1}{2}Kx^{2}[/tex]
[tex]T=\frac{1}{2}\times \frac{A^{2}}{9}[/tex]
So, the ratio of potential energy to the total energy is given by
U / T = 1 / 9
(c) Let at a displacement y the kinetic energy is equal to the potential energy
[tex]\frac{1}{2}\times K\times \left ( A^{2}-y^{2} \right )=\frac{1}{2}\times K\times y^{2}[/tex]
[tex]y=\frac{A}{\sqrt{2}}[/tex]
You are driving at 75 km/h. Your sister follows in the car behind at 75 km/h. When you honk your horn, your sister hears a frequency You are driving at 75 . Your sister follows in the car behind at 75 . When you honk your horn, your sister hears a frequency lower than the frequency you hear. higher than the frequency you hear. the same as the frequency you hear. You cannot tell without knowing the horn's frequency.
The ideal concept for solving this question is based on the Doppler effect, for which it is indicated that the source's listening frequency changes as the distance and the relative speed between the receiver and the transmitter are also changed. However, if the relative velocity between the two objects is zero as in the particular case presented (since both travel at 75km / h) we have that there will be no change in frequency.
Therefore the frequency that I hear and that my sister would listen would be the same.
An ideal gas is compressed isothermally to one-third of its initial volume. The resulting pressure will be
a. three times as large as the initial value.
b. less than three times as large as the initial value.
c. more than three times as large as the initial value.
d. equal to the initial value.
e. impossible to predict on the basis of this data. 1
Answer: a. three times as large as the initial value.
Explanation:
To calculate the new pressure, we use the equation given by Boyle's law. This law states that pressure is inversely proportional to the volume of the gas at constant temperature (isothermal).
The equation given by this law is:
[tex]P_1V_1=P_2V_2[/tex]
where,
[tex]P_1\text{ and }V_1[/tex] are initial pressure and volume.
[tex]P_2\text{ and }V_2[/tex] are final pressure and volume.
We are given:
[tex]P_1=p\\V_1=v\\P_2=?\\V_2=\frac{v}{3}[/tex]
Putting values in above equation, we get:
[tex]p\times v=P_2\times \frac{v}{3}\\\\P_2=3p[/tex]
Thus the resulting pressure will be three times as large as the initial value.
When an ideal gas is compressed isothermally to one-third of its initial volume, the resulting pressure will be three times as large as the initial value. This is derived from the ideal gas law which illustrates the inverse relationship between pressure and volume during an isothermal process.
Explanation:The behavior of an ideal gas during an isothermal compression can be understood using the ideal gas law, which states that the Pressure times the Volume (PV) equals the number of gas moles (n), times the gas constant (R), times the temperature (T). Symbolically, this can be written as PV=nRT. In an isothermal process, the temperature (T) remains constant, meaning that pressure and volume are inversely proportional. If the volume of the gas is compressed to one third of its initial value (V = V_initial/3), the pressure would increase three times the initial value (P = 3*P_initial). Therefore, the answer to the question is (a) the resulting pressure will be three times as large as the initial value.
Learn more about Ideal Gas Law here:https://brainly.com/question/1063475
#SPJ3
Ten narrow slits are equally spaced 2.00 mm apart and illuminated with green light of wavelength 511 nm. The width of bright fringes can be calculated as the separation between the two adjacent dark fringes on either side. Find the angular widths (in rad) of the third- and fifth-order bright fringes. third-order bright fringe rad fifth-order bright fringe rad
Answer:
The width of third and fifth order bright fringe is 0.00076 rad and 0.00127 rad.
Explanation:
Given that,
Distance d = 2.00 mm
Wavelength = 511 nm
Order number = 3
Order number = 5
We need to calculate the width of third-order bright fringe
Using formula of width
[tex]d\sin\theta=m\lambda[/tex]
[tex]\theta=\sin^{-1}\dfrac{m\lambda}{d}[/tex]
Put the value into the formula
[tex]\theta=\sin^{-1}\dfrac{3\times511\times10^{-9}}{2.00\times10^{-3}}[/tex]
[tex]\theta=0.00076\ rad[/tex]
We need to calculate the width of fifth-order bright fringe
Using formula of width
[tex]d\sin\theta=m\lambda[/tex]
[tex]\theta=\sin^{-1}\dfrac{m\lambda}{d}[/tex]
Put the value into the formula
[tex]\theta=\sin^{-1}\dfrac{5\times511\times10^{-9}}{2.00\times10^{-3}}[/tex]
[tex]\theta=0.00127\ rad[/tex]
Hence, The width of third and fifth order bright fringe is 0.00076 rad and 0.00127 rad.
A person sitting in a parked car hears an approaching ambulance siren at a frequency f1. as it passes him and moves away, he hears a frequency f2. the actual frequency f of the source is (which one of the following)
a. f > f1
b. f < f2
c.f= f2 - f1
d. f = f2 + f1
e. f2 < f < f1
Answer:E
Explanation:
This can be explained by Doppler effect which gives the relation between apparent Frequency and actual frequency when the source of sound is moving
[tex]f'=f\frac{v+v_o}{v-v_s}[/tex]
where [tex]f'=apparent\ frequency [/tex]
[tex]f=actual\ frequency[/tex]
[tex]v=velocity\ of\ sound[/tex]
[tex]v_o=velocity\ of\ observer[/tex]
[tex]v_s=velocity\ of\ source[/tex]
here [tex]v_o =0[/tex] as observer is standing
when Ambulance is approaching then velocity of sound and velocity of ambulance have relative velocity thus denominator is less than and apparent frequency is more while when ambulance is going away then velocity of sound waves and velocity of observer is in opposite direction thus denominator is less than 1 and apparent frequency is less.
Thus [tex]f_2<f<f_1[/tex]
The Doppler effect explains the changes in sound frequency from a moving source as perceived by a stationary observer. The observed frequency increases as the source approaches and decreases when it moves away. Hence, the actual frequency of the source (the siren) is less than the frequency observed when the source is approaching (f1) and greater than the frequency observed than when it is retreating (f2). The correct answer is 'e. f2 < f < f1'.
Explanation:This question relates to the phenomenon of the Doppler effect, which is the change in frequency or wavelength of a wave in relation to an observer who is moving relative to the wave source. In this case, when an ambulance with a siren is approaching a static observer, the observed frequency f1 will be higher than the actual frequency f (the frequency of the siren when you are sitting inside the ambulance), due to compression of the sound waves.
However, when the ambulance starts moving away from the observer, the observed frequency f2 will be lower than f, due to elongation or stretching out of the sound waves. Hence, the correct answer is 'e. f2 < f < f1'.
Learn more about Doppler effect here:https://brainly.com/question/15318474
#SPJ3
On the other side of the pivot point an adult pushes straight down on the teeter-totter with a force of 190 N. Determine the direction the teeter-totter will rotate if the adult applies the force at each of the following distances from the pivot. (Assume the teeter-totter is horizontal when the adult applies the force and that the child's weight applies a clockwise torque.)
The question seems incomplete. I found a similar version with different details. For the purpose of helping you answering the question, I will use the details from the original questions added with the sub-questions from other question. You can change the details accordingly using the explanation given below:
At the local playground, a 21-kg child sits on the right end of a horizontal teeter-totter, 1.8 m from the pivot point. On the other side of the pivot point an adult pushes straight down on the teeter-totter with a force of 190 N. Determine the direction the teeter-totter will rotate if the adult applies the force at each of the following distances from the pivot. (Assume the teeter-totter is horizontal when the adult applies the force and that the child's weight applies a clockwise torque.)
(a) 3.0 m
(b) 2.5 m
(c) 1.5 m
Answer:
a) anticlockwise
b) anticlockwise
c) clockwise
Explanation:
To answer this question, we will need the knowledge of moment/torque
Torque, T = r*Fsinθ
r = radial distance from pivot to force, F
F = Force in the direction perpendicular to the distance
θ = angle between force line and r line
Note that the direction of movement will be affected by total torque on the system. Assuming both adult and the child is initially sitting on the same level, we'll have force due to the child weight and adult force going downward and perpendicular to their respective seat on teeter-totter.
Hence,
θ = 90 degrees -> sinθ = 1
Therefore,
T = r*F(1)
T = r*F
RHS:
Torque of the child,
Tc = 1.8(21*9.8) = 370.44 Nm
LHS:
Torque of adult
Ta = d(190) =190d
with d as the distance of the adult from pivot
a) d = 3.0m
Ta = 190*3 = 570 Nm
Ta > Tc. Therefore the teeter-totter will rotate towards the adult side (LHS - going anti-clockwise)
b) d = 2.5m
Ta = 190*2.5 = 475 Nm
Ta > Tc. Therefore the teeter-totter will rotate towards the adult side (LHS - going anti-clockwise)
c) d = 1.5m
Ta = 190*1.5 = 285
Ta < Tc. Therefore the teeter-totter will rotate towards the child side (RHS - going clockwise)
An 80- kg quarterback jumps straight up in the air right before throwing a 0.43-kg football horizontally at 15m/s . Sort the following quantities as known or unknown. Take the horizontal direction to be along the x axis. : the mass of the quarterback, : the mass of the football, : the horizontal velocity of quarterback before throwing the ball, : the horizontal velocity of football before being thrown, : the horizontal velocity of quarterback after throwing the ball, : the horizontal velocity of football after being thrown
Explanation:
Given that,
Mass of the quarterback, m = 80 kg
Mass of the football, m' = 0.43 kg
Speed of the football, v' = 15 m/s
We need to sort the following quantities as known or unknown.
1. The mass of the quarterback = known = 80 kg
2. The mass of the football = known = 0.43 kg
3. The horizontal velocity of quarterback before throwing the ball = known = 0
4. The horizontal velocity of football before being thrown = known = 0
5. The horizontal velocity of quarterback after throwing the ball, = unknown quantity and it can be calculated using the conservation of linear momentum.
6. The horizontal velocity of football after being thrown = known = 15 m/s
Hence, this is the required solution.
A He-Ne laser produces light of 633 nm wavelength, 1.5 mW power, with a cylindrical beam of 0.64 mm in diameter.
(a) What is the intensity of this laser beam?
(b) The damage threshold of the retina is 100 W/m2 . Is this laser safe to view head-on?
(c) What are the maximum values of the electric and magnetic fields?
(d) What is the average energy density in the laser beam?
Final answer:
The intensity of the laser beam can be calculated from the given power and beam area, which is needed to assess safety for retinal exposure. The max electric and magnetic fields depend on the intensity and constants from electromagnetic wave equations. The average energy density is the ratio of beam intensity to the speed of light.
Explanation:
Calculating Intensity and Assessing Laser Safety:
(a) To find the intensity of the laser beam, we use the formula: I = P / A, where P is the power and A is the area of the beam. The power is given as 1.5 mW, which is 1.5 x 10-3 W. The area, given the diameter of the beam is 0.64 mm, can be calculated using the area of a circle, πr2 (where r is the radius in meters). So, the intensity is:
I = (1.5 x 10-3 W) / (π x (0.64 x 10-3 m / 2)2) = Intensity Value in W/m2.
(b) To determine if the laser is safe for the retina, we compare its intensity to the damage threshold of the retina, which is 100 W/m2. If the calculated intensity is less than this value, then the laser is considered safe for direct viewing.
(c) The maximum values of the electric (E) and magnetic (B) fields can be found using the following relationships, which are derived from the electromagnetic wave equations: E = cB, where c is the speed of light, and B = √(2I/ε0c), where ε0 is the vacuum permittivity.
(d) The average energy density of the beam can be found using: u = E / c, where u is the energy density and E is the intensity of the beam.
Which technology category would NOT likely be the subject of a standard published by the International Electrotechnical Commission (IEC)?
A. Semiconductors
B. Solar energy
C. Encryption
D. Consumer appliances
Encryption would not likely be the subject of a standard published by the International Electrotechnical Commission (IEC).
Answer: Option C
Explanation:
IEC (International Electrotechnical Commission) is the world's number one organization that develops and releases international standards for all electronic-electrical technologies and its affiliates.
Its standards would cover a wide technology range, from energy generation, transmissions and distributions to house appliances and offices, semiconductors, batteries, fibreglass, solar energy, Nano-technology and sea energy and many more.
IEC standards apply to all electrical technologies, including electronics, magnets and electro-magnetics, electro-acoustics, multi-media, telecommunications, and medical technologies, as well as related general fields such as terminology and symbols, etc.
If a projectile is fired straight up at a speed of 10 m/s, the time it takes to reach the top of its path is about
A. 1 second.
B. 2 seconds.
C. 10 seconds
D. not enough information to estimate
Answer:
A. The time it takes the projectile to reach the top of its path is about 1 second.
Explanation:
Hi there!
The equation of the velocity of a projectile fired straight up is the following:
v = v0 + g · t
Where:
v = velocity of the projectile.
v0 = initial velocity.
g = acceleration due to gravity (≅ -9.8 m/s² considering the upward direction as positive)
t = time.
When the projectile reaches the top of its path, its velocity is zero, then, using the equation of velocity, we can solve it for the time:
v = v0 + g · t
0 = 10 m/s - 9.8 m/s² · t
t = -10 m/s / -9.8 m/s²
t = 1.0 s
The time it takes the projectile to reach the top of its path is about 1 second.
A small mirror is attached to a vertical wall, and it hangs a distance of 1.86 m above the floor. The mirror is facing due east, and a ray of sunlight strikes the mirror early in the morning and then again later in the morning. The incident and reflected rays lie in a plane that is perpendicular to both the wall and the floor. Early in the morning, the reflected ray strikes the floor at a distance of 3.80 m from the base of the wall. Later on in the morning, the ray is observed to strike the floor at a distance of 1.22 m from the wall. The earth rotates at a rate of 15.0˚ per hour. How much time (in hours) has elapsed between the two observations?
Answer:
[tex]t=2.044\ hr[/tex]
Explanation:
From the schematic we can visualize the situation and the position of the rays falling on the floor.
Considering the given data from the lowest edge of the mirror.
We get a triangle with height of 1.86 meters.In the first instance the base of the triangle is 3.8 meters.While in the second instance the base is 1.22 meters.Speed of rotation of earth, [tex]\omega=15^{\circ}\ hr^{-1}[/tex]Now applying the trigonometric ratio to known sides in the first instance:
[tex]tan\ \theta_1=\frac{1.86}{3.8}[/tex]
[tex]\theta_1=26.08^{\circ}[/tex]
Applying the trigonometric ratio to known sides in the second instance:
[tex]tan\ \theta_2=\frac{1.86}{1.22}[/tex]
[tex]\theta_2=56.74^{\circ}[/tex]
Now by the law of reflection we know that the angle of incidence is equal to the angle of reflection. So the sun would have been at the same angle on the opposite side of the normal.
Hence the change in angle of the sun with respect to the mirror (also the earth)
[tex]\Delta \theta=\theta_2-\theta_1[/tex]
[tex]\Delta \theta=56.74-26.08[/tex]
[tex]\Delta \theta=30.66^{\circ}[/tex]
Now the time past for this change:
[tex]t=\frac{\Delta \theta}{\omega}[/tex]
[tex]t=\frac{30.66}{15}[/tex]
[tex]t=2.044\ hr[/tex]
A liquid of density 1370 kg/m 3 flows steadily through a pipe of varying diameter and height. At Location 1 along the pipe, the flow speed is 9.67 m/s and the pipe diameter d 1 is 12.9 cm . At Location 2, the pipe diameter d 2 is 16.7 cm . At Location 1, the pipe is Δ y = 9.85 m higher than it is at Location 2. Ignoring viscosity, calculate the difference Δ P between the fluid pressure at Location 2 and the fluid pressure at Location 1.
Answer:
ΔP = P₂ - P₁ = 132. 24 kPa
Explanation:
Given:
ρ = 1370 kg / m³ , v = 9.67 m / s , d₁ = 12.9 cm , d₂ = 16.7 cm , Δy = 9.85 m
Using Bernoulli's equations to determine the difference ΔP
P₂ + ρ * g * Z₂ + (ρ * V₂²) / 2 = P₁ + ρ * g * Z₁ + (ρ * V₁²) / 2
P₂ - P₁ = ρ * g * (Z₁ - Z₂) + [ ρ * (V₁² - V₂²) ] / 2
P₂ - P₁ = ρ * g * (Z₁ - Z₂) + ¹/₂ * ρ * V₁² * [ ( 1 - (d₁ / d₂) ⁴ ) ]
ΔP = 1370 kg / m³ * 9.8 m/s² * 9.85m + 0.5 * 1370 kg / m³ * ( 1 - (12.9 cm / 16.7 cm )⁴ )
ΔP = 132247.9364 Pa
ΔP = 132. 24 kPa
Answer:
P₂ - P₁=173.5kPa
Explanation:
The equation of continuity:
A₁v₁=A₂v₂
where A₁=πd₁²/4 and A₂=πd₂²/4
v₂=(A₁/A₂)v₁
v₂={(πd₁²/4)/(πd₂²/4)}v₁
v₂=(d₁²/d₂²)v₁
Use Bernoulli's equation
P₂+pgz₂+(pv₂²/2)=P₁+pgz₁+(pv₁²/2)
The difference between the fluid pressure at location 2 and the fluid pressure at location 1
P₂ - P₁=pg(z₁-z₂)+{p(v₁²-v₂²)}/2=pg(z₁-z₂)+1/2pv₁²(1-(d₁/d₂)⁴)
P₂ - P₁=(1.370×10³×9.8×9.85)+(1/2)(1.370×10³×(9.67)²){(1-(0.129m/0.167m)⁴}
P₂ - P₁=1.735×10⁵Pa
P₂ - P₁=173.5kPa
A welder using a tank of volume 7.20 x 10^−2 m^3 fills it with oxygen (with a molar mass of 32.0 g/mol ) at a gauge pressure of 3.20 x 10^5 Pa and temperature of 39.0°C. The tank has a small leak, and in time some of the oxygen leaks out. On a day when the temperature is 20.9 °C, the gauge pressure of the oxygen in the tank is 1.85 x 10^5 Pa.
Part A) Find the initial mass of oxygen.
Part B) Find the mass of oxygen that has leaked out.
Answer:
a) the initial mass of O₂ is 373.92 gr
b) the mass leaked of O₂ is 104.26 gr
Explanation:
we can assume ideal gas behaviour of oxygen , then we can calculate the mass using the ideal gas equation
P*V = n*R*T ,
where P= absolute pressure , V= volume occupied by the gas , n = number of moles of gas , R= ideal gas constant = 8.314 J/mol K , T= absolute temperature
Initially
P = Pg + Pa ( 1 atm) = 3.20 *10⁵ Pa + 101325 Pa = 4.21*10⁵ Pa
where Pg= gauge pressure , Pa=atmospheric pressure
T = 39 °C= 312 K
V= 7.20 * 10⁻² m³
therefore
P*V = n*R*T → n = P*V/ (R*T)
replacing values
n = P*V/ (R*T) = 4.21*10⁵ Pa*7.20 * 10⁻² m³/(8.314 J/mol K*312 K) = 11.685 mol
since
m= n*M , where m= mass , n= number of moles , M= molecular weight of oxygen
then
m = n*M = 11.685 mol *32.0 g/mol = 373.92 gr of O₂
therefore the initial mass of O₂ is 373.92 gr
for the part B)
P₂= Pg₂ + Pa ( 1 atm) = 1.85*10⁵ Pa + 101325 Pa = 2.86*10⁵ Pa
T₂ = 20.9 °C= 293.9 K
V= 7.20 * 10⁻² m³
therefore
n₂ = P₂*V/ (R*T₂) = 2.86*10⁵ Pa*7.20 * 10⁻² m³/(8.314 J/mol K*293.9 K) = 8.427 mol
m₂ = n*M = 8.427 mol*32.0 g/mol = 269.66 gr of O₂
thus the mass leaked of oxygen is
m leaked = m - m₂ = 373.92 gr - 269.66 gr = 104.26 gr
Suppose that, at t = 9.00 × 10 − 4 s, the space coordinates of a particle are x = 135 m, y = 30.0 m, and z = 55.0 m according to coordinate system S . If reference frame S ′ moves at speed 1.50 × 10 5 m/s in the + x - direction relative to frame S , compute the corresponding coordinate values as measured in frame S ′ . The reference frames start together, with their origins coincident at t = 0 .
Answer:
[tex]x'=134.999983\ m[/tex]
[tex]y'=y=30\ m[/tex]
[tex]z'=z=55\ m[/tex]
Explanation:
Given:
time, [tex]t=9\times 10^{-4}\ s[/tex]x coordinates of a particle, [tex]x=135\ m[/tex]y coordinates of a particle, [tex]y=30\ m[/tex]z coordinates of a particle, [tex]x=55\ m[/tex]Relative Speed of frame of reference S' in the +x direction, [tex]v_x=1.5\times 10^{5} m.s^{-1}[/tex]Since the speed of the frame S' is comparable to the speed of light in vacuum therefore the observer from S' frame will observe a contracted length of the dimensions in the direction of motion.Now from the equation of length contraction:
[tex]x'=x\times \sqrt{1-\frac{v_x^2}{c^2} }[/tex]
[tex]x'=135\times \sqrt{1-\frac{(1.5\times 10^{5})^2}{(3\times 10^8)^2} }[/tex]
[tex]x'=134.999983\ m[/tex]
Rest other values will remain unaffected since they are along the axis of motion. So,
[tex]y'=y=30\ m[/tex]
[tex]z'=z=55\ m[/tex]
A ladder whose length L is 12 m and mass m is 45 kg rests against a wall. Its upper end is a distance h of 9.3 m above the ground. The center of mass of the ladder is one-third of the way up the ladder. A fire fighter whose mass M is 72 kg climbs the ladder until his center of mass is halfway up. Assume the wall but not the ground is frictionless. What forces are exerted on the ladder by the wall and by the ground? Provide both the magnitude and direction of the ground force.
Answer:
FN₁ = 1146.6N : Force exerted on the ladder by the floor , vertical and upward
FN₂ = 407.5 N : Force exerted on the ladder by the wall , horizontal and opposite to friction force between the floor and the ladder
Explanation:
The equilibrium equation are:
∑Fx=0
∑Fy=0
∑M = 0
M = F*d
Where:
∑M : Algebraic sum of moments
M : moment ( N*m)
F : Force ( N)
d :Perpendicular distance of the force to the point ( meters )
Data
m =45 kg : mass of the ladder
M =72 kg : mass of the fire fighter
g = 9.8 m/s²: acceleration due to gravity
L = 12 m : ladder length
h = 9.3 m: ladder height
L/3 = 12/3 = 4m Location of the center of mass of the ladder of the way up
L/2 = 12/2 = 6m Location of the center of mass of the fire fighter
µ = 0 : coefficient of friction between the ladder and the wall
θ : angle that makes the ladder with the floor
sinθ = h/L = 9.3 m/12 m
θ =sin⁻¹( 9.3 / 12)
θ = 50.8°
Forces acting on the ladder
W₁ =m*g = 45 kg* 9.8 m/s² = 441 N: Weight of the ladder (vertical downward)
W₂ =M*g = 72 kg * 9.8 m/s² = 705.6 N : Weight of the fire fighter(vertical downward)
FN₁ :Normal force that the floor exerts on the ladder (vertical upward) (point A)
fs : friction force that the floor exerts on the ladder (horizontal and opposite the movement )(point A)
FN₂ : Normal Force that the wall exerts on the ladder ( horizontal and opposite to friction force between the floor and the ladder)
∑Fy=0
FN₁ -W₁ -W₂= 0
FN₁ = W₁ + W₂
FN₁ = 441N+ 705.6N
FN₁ = 1146.6N : Force exerted on the ladder by the wall (vertical and upward)
Calculation of the distances of the forces at the point A (contact point of the ladder on the floor)
d₁ = 4*cos 50.8° (m) = 2.53 m: Distance from W₁ to the point A
d₂ =6*cos 50.8° (m)= 3.79 m : Distance from W₂ to the point A
d₃ = 9.3 m : Distance from FN₂ to the point A
The equilibrium equation of the moments at the point A (contact point of the ladder with the floor)
∑MA = 0
FN₂(d₃) - W₁( d₁) - W₂(d₂) = 0
FN₂(d₃) = W₁(d₁) + W₂(d₂)
FN₂(9.3) = (441 )(2.53) + (705.6)( 3.79 )
FN₂(9.3) = 1115.73 + 2674.2
FN₂ = (3790) / (9.3)
FN₂ = 407.5 N : Force exerted on the ladder by the wall , horizontal and opposite to friction force between the floor and the ladder
Force excreted by floor on ladder is 1146.6 N (vertically upward) and force excreted by wall on ladder is 407.5 N (horizontally towards the normal force).
What is force?Force is the effect of pull or push due to which the object having a mass changes its velocity.
The force is of two types-
Push-When the force applied in the direction of motion of the object, then the force is called the push force. Pull- When the force applied in the opposite direction of motion of the object, then the force is called the pull force.The length of the ladder is 12 meter and the mass of the ladder is 45 kg.Its upper end is a distance h of 9.3 and the mass of fire fighter is 72 kg.
The sine angle for the ladder can be given as,
[tex]\sin\theta=\dfrac{9.3}{12}\\\theta=50.8^o[/tex]
The forces acting on the system is normal force and force due to the weight of the two bodies.
The summation of the vertical forces is equal to the zero to keep it at rest. Therefore,
[tex]F_n-45\times9.8-72\times9.8\\F_n=1146.6 \rm N[/tex]
By the equilibrium of the momentum for the system,
[tex]F_{N2}\times(9.3)+45(9.8)\times(4\cos50.8)+72(9.8)\times(6\cos50.8)\\F_{N2}=407.5\rm N[/tex]
Thus, the force excreted by the floor on ladder is 1146.6 N (vertically upward) and the force excreted by the wall on ladder is 407.5 N (horizontally towards the normal force).
Learn more about the force here;
https://brainly.com/question/388851
A propeller consists of two blades each 3.0 m in length and mass 120 kg each. The propeller can be approximated by a single rod rotating about its center of mass. The propeller starts from rest and rotates up to 1200 rpm in 30 seconds at a constant rate.
a) What is the angular momentum of the propeller at ????=10s;????=20s?
b) What is the torque on the propeller?
Answer:
Explanation:
a)
[tex]l[/tex] = length of each blade = 3 m
[tex]m[/tex] = mass of each blade = 120 kg
[tex]L[/tex] = length of the rod
[tex]M[/tex] = mass of the rod
Length of the rod is given as
[tex]L = 2 l = 2 (3) = 6 m[/tex]
[tex]w_{0}[/tex] = Angular velocity at t = 0, = 0 rad/s
[tex]w_{30}[/tex] = Angular velocity at t = 30, = 1200 rpm = 125.66 rad/s
[tex]\Delta t[/tex] = time interval = 30 - 0 = 30 s
angular acceleration is given as
[tex]\alpha = \frac{w_{30} - w_{0}}{\Delta t} = \frac{125.66 - 0}{30} = 4.2 rad/s^{2}[/tex]
Angular velocity at t = 10 s is given as
[tex]w_{10} = w_{0} + \alpha t\\w_{10} = 0 + (4.2) (10)\\w_{10} = 42 rad/s[/tex]
Angular velocity at t = 20 s is given as
[tex]w_{20} = w_{0} + \alpha t\\w_{20} = 0 + (4.2) (20)\\w_{10} = 84 rad/s[/tex]
Mass of the rod is given as
[tex]M = 2m = 2(120) = 240 kg[/tex]
Moment of inertia of the propeller is given as
[tex]I = \frac{ML^{2} }{12} = \frac{(240)(6)^{2} }{12} = 720 kgm^{2}[/tex]
Angular momentum at t = 10 s is given as
[tex]L_{10} = I w_{10} = (720) (42) = 30240 kgm^{2}/s[/tex]
Angular momentum at t = 20 s is given as
[tex]L_{20} = I w_{20} = (720) (84) = 60480 kgm^{2}/s[/tex]
b)
Torque on propeller is given as
[tex]\tau = I \alpha \\\tau = (720) (4.2)\\\tau = 3024 Nm[/tex]
Answer:
(a) 4800 kg m^2/s^2 , 9600 kg m^2/s^2
(b) 480 Nm
Explanation:
length of each blade = 3 m
total length, L = 2 x 3 = 6 m
mass of each blade = 120 kg
total mass, m = 2 x 120 = 240 kg
initial angular velocity, ωo = 0 rad/ s
final angular velocity, ω = 1200 rpm = 1200 / 60 = 20 rps = 125.6 rad/s
t = 30 s
Let the angular acceleration is α.
α = (ω - ωo)/t = 120 / 30 = 4 rad/s^2
(a) moment of inertia. I = mL^2 / 12
I = 240 x 6 / 12 = 120 kg m^2
Let ω' be the angular velocity at the end of 10 s
use first equation of motion
ω' = 0 + αt
ω' = 4 x 10 = 40 rad/s
Angular momentum at t = 10 s
L = I x ω = 120 x 40 = 4800 kg m^2/s^2
Let ω'' be the angular velocity at the end of 20 s
use first equation of motion
ω'' = 0 + αt
ω'' = 4 x 20 = 80 rad/s
Angular momentum at t = 20 s
L = I x ω = 120 x 80 = 9600 kg m^2/s^2
(b) Torque, τ = I x α
τ = 120 x 4 = 480 Nm
19.55 The 8-kg uniform bar AB is hinged at C and is attached at A to a spring of constant k 5 500 N/m. If end A is given a small displace- ment and released, determine
(a) the frequency of small oscillations,
(b) the smallest value of the spring constant k for which oscillations will occur.
Answer:
Explanation:
C is center of mass of the bar ie middle point. Spring is attached with one end ie A of the bar . When this end is displaced by distance x ( small) a restoring force kx is produced which creates a torque
Torque created = kx . l /2 , which creates angular acceleration α
moment of inertia I = ml²/12
torque = I. x α
kx . L /2 = I. x α
α = L kx / 2I
a = linear acceleration
= α x L/2
= L² kx / 4I
= L²x 12 kx / 4 mL²
a = 3kx/m
This shows that motion is SHM as acceleration is proportional to displacement x .
angular frequency ω² = 3k / m
frequency f = 1/2π √ 3k/m
= (1/6.28) x √ 3x 500/8
= 2.18 Hz
Final answer:
The frequency of small oscillations is approximately 3.98 Hz, and the smallest value of the spring constant for which oscillations will occur is 0 N/m.
Explanation:
(a) To determine the frequency of small oscillations, we can use the formula: f = (1/2π) × (√(k/m)), where f is the frequency, k is the spring constant, and m is the mass of the bar. Plugging in the values, we get:
f = (1/2π) × (√(500/8)) ≈ 3.98 Hz
(b) To find the smallest value of the spring constant k for which oscillations will occur, we need to consider critical damping. Critical damping occurs when the damping force is equal to the force exerted by the spring. The formula for critical damping is c = 2√(mk), where c is the damping coefficient, m is the mass, and k is the spring constant. Since we know that the damping coefficient is 0, we can solve for k to get:
k = (c^2)/(4m). Substituting in the values, we get:
k = (0^2)/(4 x 8) = 0 N/m
How much is the moment due to force P about point B. P(unit=N) vector is equal to (150i+260j ) and vector BA (unit=meter) is equal to (0.23i+0.04j)?
Answer:
The moment (torque) is given by the following equation:
[tex]\vec{\tau} = \vec{r} \times \vec{F}\\\vec{r} \times \vec{F} = \left[\begin{array}{ccc}\^{i}&\^j&\^k\\r_x&r_y&r_z\\F_x&F_y&F_z\end{array}\right] = \left[\begin{array}{ccc}\^{i}&\^j&\3k\\0.23&0.04&0\\150&260&0\end{array}\right] = \^k((0.23*260) - (0.04*150)) = \^k (53.8~Nm)[/tex]
Explanation:
The cross-product between the distance and the force can be calculated using the method of determinant. Since the z-components are zero, it is easy to calculate.
Charge of uniform density (40 pC/m^2) is distributed on a spherical surface (radius = 1.0 cm), and a second concentric spherical surface (radius = 3.0 cm) carries a uniform charge density of 60 pC/m2. What is the magnitude of the electric field at a point 4.0 cm from the center of the two surfaces?1. 5.6 N/C2. 4.5 N/C3. 1.1 N/C4. 1.4 N/C5. 0.50 N/C
Answer:
The magnitude of the electric field at a point 4.0 cm from the center of the two surfaces is 4.10 N/C
Explanation:
Step 1: Data given
Charge of uniform density of first sphere= 40 pC/m² = 40.0 * 10^-12 C/m²
Radius of first sphere is 1.0 cm
Radius of second sphere = 3.0 cm
Charge of uniform density of second sphere= 60 pC/m² = 60.0 * 10^-12 C/m²
Step 2: Calculate the magnitude
Sphere surface area = 4πr²
Charge on inner sphere Qi = 40.0*10^-12C/m² * 4π(0.01m)² = 5.027*10^-14 C
NET charge on outer sphere Qo = 60.0*10^-12 * 4π(0.03m)² = 6.786*10^-13 C
Inner sphere induces a - 5.027*10^-14 C charge (-Qi) on inside of the outer shell
This means there is a net zero charge within the outer shell.
For the outer shell to show a NET charge +6.786*10^-13C, it's must have a positivie charge {+6.786*10^-13C + (+5.027*10^-14C)} = +7.2887*10^-13 C
Regarding the outer shell as a point charge (field at 0.04m is)
E = kQ /r²
E = (8.99^9)*(7.2887*10^-13 C) / (0.04)² .. .. ►E = 4.10 N/C
========
Using Gauss's law .. with a spherical Gaussian surface at 0.04m enclosing a net charge +7.2887*10^-13 C
Flux EA = Q / εₒ
⇒ with εₒ = 8.85 *10^-12
⇒ with Q = 7.2887*10^-13 C
E * 4π(0.04)² = 7.2887*10^-13 C / 8.85*10^-12
E = 7.2887*10^-13 C / {8.85*10^-12 * 4π(0.04)²}
E = 4.10 N/C
The magnitude of the electric field at a point 4.0 cm from the center of the two surfaces is 4.10 N/C
A correct option is option (2).
Given,
The Surface area of a sphere [tex]A=4\pi r^2[/tex]
Find the charge on the inner sphere.
[tex]Q_i =40.0^{2} c/m^2\times4\pi (0.01m)^2\\=5.03^{-14 C}[/tex]
In this case, the Inner sphere induces a [tex]5.03^{-14 C}[/tex]charge [tex](-Q_i)[/tex] on the inside of the outer shell.
Therefore, there is a net-zero charge within the outer shell.
For the outer shell to show a net charge [tex]+6.79^{-13}C[/tex], it's must have a +ve charge.
[tex]{+6.79^{-13} C + (+5.03^{-14} C)} = +7.29^{-13} C[/tex]
Now, Use Gauss's law, with a spherical Gaussian surface at 0.03m enclosing a net charge[tex]+7.29^{-13} C[/tex]
[tex]Flux=E_A\\=\frac{Q}{\varepsilon _0 }[/tex]
Substitute numerical values we get,
[tex]E\times4\pi (0.04)^2=\frac{.29^{-13} }{8.85^{-12} } \\E=4.5 N/C[/tex]
Learn More: https://brainly.com/question/22990844
Suppose F is a radial force field, S1 is a sphere of radius 4 centered at the origin, and the flux integral ∫∫S1F⋅dS=8.Let S2 be a sphere of radius 16 centered at the origin, and consider the flux integral ∫∫S2F⋅dS.(A) If the magnitude of F is inversely proportional to the square of the distance from the origin,what is the value of ∫∫S2F⋅dS?(B) If the magnitude of F is inversely proportional to the cube of the distance from the origin, what is the value of ∫∫S2F⋅dS?
A. [tex]\( \iint_{S_2} F \cdot dS = 128 \)[/tex]
B. [tex]\( \iint_{S_2} F \cdot dS = 128 \)[/tex]
(A) If the magnitude of (F) is inversely proportional to the square of the distance from the origin:
We know that the flux integral over [tex]\( S_1 \)[/tex] is [tex]\( \iint_{S_1} F \cdot dS = 8 \)[/tex].
Since ( F ) is a radial force field, (F) and (dS) are parallel, and the dot product simplifies to [tex]\( |F| \cdot |dS| \)[/tex].
The surface area of a sphere is [tex]\( 4\pi r^2 \)[/tex], so the magnitude of [tex]\( dS \)[/tex] on [tex]\( S_1 \)[/tex] is [tex]\( |dS| = 16\pi \)[/tex].
Therefore, [tex]\( |F| \cdot |dS| = 8 \implies |F| \cdot 16\pi = 8 \)[/tex], which gives [tex]\( |F| = \frac{1}{2\pi} \)[/tex].
For [tex]\( S_2 \)[/tex], with radius 16, [tex]\( |dS| = 256\pi \)[/tex].
So, [tex]\( \iint_{S_2} F \cdot dS = |F| \cdot 256\pi = \frac{1}{2\pi} \cdot 256\pi = 128 \)[/tex].
(B) If the magnitude of (F) is inversely proportional to the cube of the distance from the origin:
For [tex]\( S_1 \)[/tex], [tex]\( |dS| = 16\pi \)[/tex] as before. So, [tex]\( |F| \cdot |dS| = 8 \implies |F| = \frac{1}{2} \)[/tex].
For [tex]\( S_2 \)[/tex], [tex]\( |dS| = 256\pi \)[/tex] as before.
So, [tex]\( \iint_{S_2} F \cdot dS = |F| \cdot 256\pi = \frac{1}{2} \cdot 256\pi = 128 \)[/tex].
The temperature of the Sun’s atmosphere near the surface is about 6000 K, and the concentration of atoms is about 1015 particles/m3. What are the average pressure and density of its atmosphere? What assumptions did you make to solve the problem?
Answer:
average pressure = 8.314 ×[tex]10^{-5}[/tex] pascal
density = 1.66 ×[tex]10^{-12}[/tex] kg/m³
Explanation:
given data
temperature of sun = 6000 K
concentration of atoms = [tex]10^{15}[/tex] particles/m³
to find out
average pressure and density of its atmosphere
solution
first we get here average pressure of atmosphere that is express as
average pressure = [tex]\frac{nRT}{V}[/tex] .............1
put here value we get
average pressure = [tex]\frac{10^15*8.314*6000}{6*10^{23}}[/tex]
average pressure = 8.314 ×[tex]10^{-5}[/tex] pascal
and
density of atmosphere will be
density = [tex]\frac{nM}{V}[/tex] .............2
density = [tex]\frac{10^{15}*1.66*10^{-27}}{1}[/tex]
density = 1.66 ×[tex]10^{-12}[/tex] kg/m³
A grocery shopper tosses a(n) 9.1 kg bag of
rice into a stationary 19.3 kg grocery cart.
The bag hits the cart with a horizontal speed
of 6.6 m/s toward the front of the cart.
What is the final speed of the cart and bag?
Answer in units of m/s.
Answer:
2.1 m/s
Explanation:
Momentum is conserved, so:
m₁ u₁ + m₂ u₂ = (m₁ + m₂) v
(9.1 kg) (6.6 m/s) = (9.1 kg + 19.3 kg) v
v = 2.1 m/s