Answer:
[tex]\frac{Q}{Q_0}=1[/tex]
Explanation:
Capacitance is defined as the charge divided in voltage.
[tex]C=\frac{Q}{V}(1)[/tex]
Introducing a dielectric into a parallel plate capacitor decreases its electric field. Therefore, the voltage decreases, as follows:
[tex]V=\frac{V_0}{k}[/tex]
Where k is the dielectric constant and [tex]V_0[/tex] the voltage of the capacitor without a dielectric
The capacitance with a dielectric between the capacitor plates is given by:
[tex]C=kC_0[/tex]
Where k is the dielectric constant and [tex]C_0[/tex] the capacitance of the capacitor without a dielectric. So, we have:
[tex]Q=CV\\Q=kC_0\frac{V_0}{k}\\Q=C_0V_0\\Q_0=C_0V_0\\Q=Q_0\\\frac{Q}{Q_0}=1[/tex]
Therefore, a capacitor with a dielectric stores the same charge as one without a dielectric.
Calculate the time required (in years) for water to penetrate a layer of clay that is 40 cm deep when exposed to a hydraulic gradient of 1 cm/cm. The permeability of clay is 1x10-8 cm/sec. If there is 30 cm static head of water on the clay layer, how long will it take for moisture to penetrate the 40 cm clay layer (in years)?
Answer:
The time required to penetrate the 40 cm clay layer is 126.82 years
Explanation:
Given:
Hydraulic gradient = 1 [tex]\frac{cm}{cm}[/tex]
Permeability of clay [tex]K = 1 \times 10^{-8}[/tex] [tex]\frac{cm}{sec}[/tex]
Time required to penetrate 40 cm clay layer,
[tex]= \frac{40}{K}[/tex]
[tex]= \frac{40}{1 \times 10^{-8} }[/tex]
[tex]= 40 \times 10^{8}[/tex] sec
But we have to find time in years,
[tex]= \frac{40 \times 10^{8} }{24 \times 60 \times 60 \times 365}[/tex] years
[tex]= 126.82[/tex] years
Therefore, the time required to penetrate the 40 cm clay layer is 126.82 years
Answer:
its a
Explanation:
The slotted link is pinned at O, and as a result of the constant angular velocity u # = 3 rad>s it drives the peg P for a short distance along the spiral guide r = (0.4 u) m, where u is in radians. Determine the velocity and acceleration of the particle at the
Answer:
A) vᵣ = 1.2 m/s
B) vₜ = 0.4π m/s = 1.257 m/s
C) aᵣ = - 1.2π m/s² = - 3.771 m/s²
D) aₜ = 7.2 m/s²
Explanation:
Given,
θ' = 3 rad/s
r = 0.4 θ
Note that
θ' = (dθ/dt) = 3 rad/s
θ" = (d²θ/dt²) = (d/dt) (3) = 0 rad/s²
r' = (dr/dt) = (d/dt) (0.4θ) = 0.4 (dθ/dt) = 0.4 × θ' = 0.4 × 3 = 1.2 m/s
r" = (d²r/dt²) = 0.4 (d²θ/dt²) = 0 m/s²
A) Radial component of the velocity of P at the instant θ=π/3rad.
From the kinematics of a particle in a plane,
vᵣ = r' = 1.2 m/s
B) Transverse component of the velocity and acceleration of P at the instant θ=π/3rad.
vₜ = rθ' = (0.4 θ) (3) = 1.2 θ = 1.2 (π/3) = 0.4π m/s = 1.257 m/s
C) Radial component of the acceleration of P at the instant θ=π/3rad.
aᵣ = r" - r(θ'²) = 0 - (0.4θ)(3²) = - 3.6θ = - 3.6 (π/3) = - 1.2π m/s² = - 3.771 m/s²
D) Transverse component of the acceleration of P at the instant θ=π/3rad
aₜ = rθ" + 2r'θ' = (0.4θ)(0) + (2)(1.2)(3) = 0 + 7.2 = 7.2 m/s²
Hope this Helps!!!
The response requires understanding rotational kinematics and dynamics to determine the velocity and acceleration of a particle moving along a spiral guide, involving calculus and principles of rotational motion.
Explanation:The question pertains to kinematics in the context of rotational and spiral motion. In particular, it involves the motion of a particle along a spiral guide with a given radial dependency on the angle turned through (in radians). To find the velocity and acceleration of the particle, one must apply the equations of motion that relate linear and angular quantities and consider any given geometric relationships and constraints, such as the provided relationship between radial distance and angular position. To solve the tasks posed, one would typically employ differential calculus and the principles of rotational dynamics including tangential and radial components of velocity and acceleration.
For example, the velocity of the particle can be found by taking the time derivative of the radial position r, which in turn depends on the angular velocity ω. The acceleration would then be found by differentiating the velocity with respect to time or by explicitly using the tangential and radial acceleration components for rotational motion, which are related to ω and its time derivative (angular acceleration).
Approximately 1.000 g each of four gasses H2, Ne, Ar, and Kr are placed in a sealed container all under1.5 atm of pressure. Assuming ideal behavior, determine the partial pressure of the H2 and Ne
Answer:
The partial pressure of H2 is 0.375 atm
The partial pressure of Ne is also 0.375 atm
Explanation:
Mass of H2 = 1 g
Mass of Ne = 1 g
Mass of Ar = 1 g
Mass of Kr = 1 g
Total mass of gas mixture = 1 + 1 + 1 + 1 = 4 g
Pressure of sealed container = 1.5 atm
Partial pressure of H2 = (mass of H2/total mass of gas mixture) × pressure of sealed container = 1/4 × 1.5 = 0.375 atm
Partial pressure of Ne = (mass of Ne/total mass of gas mixture) × pressure of sealed container = 1/4 × 1.5 = 0.375 atm
The partial pressures of H2 and Ne in the mixture under ideal gas behavior are approximately 1.278 atm and 0.128 atm respectively. This is calculated using their mole fractions and the total pressure.
Explanation:In this scenario, we're essentially dealing with ideal gas behavior. The partial pressure of a gas in a mixture can be determined by the mole fraction of the gas times the total pressure. The moles of each gas can be calcuated using the equation: moles = mass/molar mass. The molar masses of H2, Ne, Ar, and Kr are approximately 2 g/mol, 20 g/mol, 40 g/mol, and 84 g/mol, respectively.
For example, moles of H2 ≈ 1.000 g / 2 g/mol = 0.5 mol. Likewise, moles of Ne = 1.000 g / 20 g/mol = 0.05 mol, moles of Ar = 1.000 g / 40 g/mol = 0.025 mol, and moles of Kr = 1.000 g / 84 g/mol = 0.012 mol. The total moles of gas = 0.5 mol + 0.05 mol + 0.025 mol + 0.012 mol = 0.587 mol.
The mole fraction of H2 = 0.5 mol / 0.587 mol = 0.852. Therefore, the partial pressure of H2 = 0.852 * 1.5 atm = 1.278 atm. Applying the same calculations for Ne, the mole fraction of Ne = 0.05 mol / 0.587 mol = 0.085. Therefore, the partial pressure of Ne = 0.085 * 1.5 atm = 0.128 atm.
Learn more about Partial Pressure here:https://brainly.com/question/35280352
#SPJ3
A 15.0 g bullet is moving to the right with speed 270 m/s when it hits a target and travels an additional 25.0 cm into the target. What are the magnitude (in N) and direction of the stopping force acting on the bullet
Answer:
[tex]F=2187\ N[/tex]
Explanation:
Given:
mass of bullet,[tex]m=15\ g=0.015\ kg[/tex] initial velocity of bullet, [tex]u=270\ m.s^{-1}[/tex]displacement of the bullet in the target, [tex]s=25\ cm=0.25\ m[/tex]Here as given in the question the bullet penetrates the target by the given displacement of the bullet into it. During this process it faces deceleration and hence it comes to rest.
so, final velocity of the bullet, [tex]v=0\ m.s^{-1}[/tex]Now using the equation of motion:
[tex]v^2=u^2+2a.s[/tex]
where:
[tex]a=[/tex] acceleration of the bullet
[tex]0^2=270^2+2a\times 0.25[/tex]
[tex]a=145800\ m.s^{-2}[/tex]
Now the force of resistance offered by the target in stopping it:
[tex]F=m.a[/tex]
[tex]F=0.015\times145800[/tex]
[tex]F=2187\ N[/tex]
person is 1.9 m tall. Where should he place the top of a mirror on the wall so he can see the top of his head? Assume his eyes are 5.1 cm below the top of his head. Find a minimal vertical distance from the level of the person’s eye
Answer:
The minimal vertical distance from the level of the person’s eye is 2.55 cm.
Explanation:
Given;
height of the person = 1.9 m
his eyes are 5.1 cm below the top of his head
If top of his head is the same distance from the mirror as his eyes is from the mirror, then the top of the mirror must be half of his eyes level.
Therefore, the minimal vertical distance from the level of the person’s eye is ¹/₂ x 5.1 cm = 2.55 cm
The minimal vertical distance of the mirror from the level of the person’s eye is 2.55 cm.
Two long parallel wires are a center-to-center distance of 4.90 cm apart and carry equal anti-parallel currents of 4.10 A. Find the magnetic field intensity at the point P which is equidistant from the wires. (R = 6.00 cm).
Answer:
The magnetic field intensity at the point P, equidistant from the wires is
9.566 x [tex]10^{-5}[/tex] T
Explanation:
The magnetic field intensity can be obtained by resolving the vertical and horizontal components of the magnetic field. The step by step calculation is contained in the pictures attached;
You have just completed the first part of this lab and have five time values for a particular height: 1.8, 1.7, 1.9, 0.8, and 1.9 seconds. a) Give one quantitative reason why you think that 0.8 sec is or is not consistent with the other measurements.
Answer: because 1.8 is an outlier.
Explanation: it can been seen that from the data given to us, 1.7, 1.8, 1.9, 1.9 are all close to each other with a difference of 0.2 or 0.1.
By considering 0.8, this value (0.8) is at a very far distance away from other observational data with a difference of at least 0.9.
This henceforth makes 0.8 an outlier ( a data which is at a far distance away from other observational data)
The 0.8-second measurement is likely inconsistent with the others due to its significant deviation from the clustered times around 1.8 seconds, pointing to it as an outlier potentially caused by an experimental error.
One quantitative reason to suspect that the time value of 0.8 seconds is inconsistent with the other measurements of 1.8, 1.7, 1.9, and 1.9 seconds is the concept of measurement uncertainties and standard deviation. When comparing the given times, we see that the majority of the values are clustered around 1.8 seconds, suggesting a certain range of natural variability in repeated measurements. However, 0.8 seconds is significantly lower than the others, indicating that it is an outlier and might have been affected by experimental error or a faulty measurement. The use of mean and standard deviation can give us a formal way to assess consistency among data. If we calculated the mean and standard deviation, we would likely find 0.8 seconds to fall outside an acceptable range based on the precision of our measurements, reinforcing the idea that this result is inconsistent with the others.
Suppose the truck that’s transporting the box In Example 6.10 (p. 150) is driving at a constant speed and then brakes and slows at a constant acceleration. While coming to a stop, the driver looks in the rear-view mirror and notices that the box is not slipping. In what direction is the frictional force acting on the box?
Answer:
Friction acts in the opposite direction to the motion of the truck and box.
Explanation:
Let's first review the problem.
A moving truck applies the brakes, and a box on it does not slip.
Now when the truck is applying brakes, only it itself is being slowed down. Since the box is slowing down with the truck, we can conclude that it is friction that slows it down.
The box in the question tries to maintains its velocity forward when the brakes are applied. We can think of this as the box exerting a positive force relative to the truck when the brakes are applied. When we imagine this, we can also figure out where the static friction will act to stop this positive force. Friction will act in the negative direction. Or in other words, friction will act in the opposite direction to the motion of the truck and box. This explains why the box slows down with the truck, as friction acts to stop its motion.
Final answer:
The frictional force acting on the box in a decelerating truck acts forward, towards the direction of the truck's original motion. This occurs as a result of trying to prevent the box from slipping backward by opposing its tendency to remain in motion, illustrating key concepts from Newton's laws of motion.
Explanation:
When the truck brakes and slows down at a constant acceleration, the box inside does not slip due to the frictional force acting on it. The direction of the frictional force on the box will be forward, towards the direction of the truck's original motion.
This might initially seem counterintuitive, but it's essential to understand that the frictional force is what keeps the box from sliding backward as the truck decelerates. According to Newton's first law of motion, an object in motion will stay in motion with the same speed and in the same direction unless acted upon by an unbalanced external force.
In this case, the frictional force acts as that external force, opposing the box's tendency to remain in motion while the truck slows down.
Friction, in physics, acts opposite to the direction of motion and is necessary for stopping the movement of objects. Since the truck is decelerating, the box tries to maintain its state of motion (Newton's first law), but the frictional force acts forward relative to the truck to prevent the box from slipping backward.
This example beautifully demonstrates the role of friction in everyday phenomena, aligning with concepts like Newton's laws of motion and the interaction between surfaces in contact.
A bullet is fired with a muzzle velocity of 1446 ft/sec from a gun aimed at an angle of 5 degrees above the horizontal. Find the vertical component of the velocity.
Answer:
126.03 ft/sec
Explanation:
From the question above,
V₁ = VsinФ............. Equation 1
Where V₁ = vertical component of the velocity, V = Velocity acting on the x-y plane, Ф = angle to the horizontal.
Given: V = 1446 ft/sec, Ф = 5°
Substitute into equation 1
V₁ = 1446sin(5)
V₁ = 1446(0.0872)
V₁ = 126.03 ft/sec.
Hence the vertical component of the velocity = 126.03 ft/sec
Suppose a sound wave and an electromagnetic wave have the same frequency. Which has the longer wavelength? 1. the electromagnetic wave 2. the sound wave
Answer:
1. the electromagnetic wave.
Explanation:
Mathematically,
wavelength = velocity ÷ frequency
A mechanical wave is a wave that is not capable of transmitting its energy through a vacuum. Mechanical waves require a medium in order to transport their energy from one location to another. A sound wave is an example of a mechanical wave. Sound waves are incapable of traveling through a vacuum.
Electromagnetic waves of different frequency are called by different names since they have different sources and effects on matter, increasing frequency decreases wavelength.
Sound waves (which obviously travel at the speed of sound) are much slower than electromagnetic waves (which travel at the speed of light.)
Electromagnetic waves are much faster than sound waves and If the Velocity of the wave increases and the frequency is constant, the wavelength also increases.
Suppose you analyze standardized test results for a country and discover almost identical distributions of physics scores for female and male students. Which of the following would NOT be an explanation based upon what you read in the textbook? Select one:
O a. Physics ability is less likely than math to reflect real biological differences.
O b. There were no gender differences in the teaching and learning of physics in this country
c. Physics ability is not defined as gendered in this country
O d . The standardized testing took place in a relatively gender equal society.
The textbook would not likely suggest 'Physics ability is less likely than math to reflect real biological differences' as an explanation for identical physics scores between genders. This because research shows academic abilities aren't influenced by biological gender differences but rather other factors like sociocultural influences, teaching methods, and individual variance.
Explanation:The statement that would not be an explanation for finding the almost identical distribution of physics scores between male and female students, based on information provided in a textbook, is a. Physics ability is less likely than math to reflect real biological differences.
This claim implies there is a biological basis for differing abilities in physics between genders. However, research has largely debunked this concept, showing that abilities in academic subjects are not influenced by biological gender differences. Instead, other factors like sociocultural influences, teaching methods, and individual variance play a significant role.
Options b, c, and d all refer to sociocultural aspects such as the way physics is taught, the societal concept of gender roles, and the equality of the society. These, not inherent biological differences, could explain identical distributions of physics scores between genders.
Learn more about Physics and Gender Differences here:https://brainly.com/question/33229071
#SPJ3
Consider an electron on the surface of a uniformly charged sphere of radius 1.2 cm and total charge 1.4 10-15 C. What is the "escape speed" for this electron
Answer:
Explanation:
electric potential of electron
= k Qq / r
= - 9 x 10⁹ x 1.4 x 10⁻¹⁵ x 1.6 x 10⁻¹⁹ / ( 1.2 x 10⁻² )
= - 16.8 x 10⁻²³ J
If v be the escape velocity
1/2 m v² = potential energy of electron
= 1/2 x 9.1 x 10⁻³¹ x v² = 16.8 x 10⁻²³
v² = 3.69 x 10⁸
v = 1.92 x 10⁴ m /s
A hockey puck is sliding across a frozen pond with an initial speed of 9.3 m/s. It comes to rest after sliding a distance of 42.0 m. What is the coefficient of kinetic friction between the puck and the ice?
Answer:
The coefficient of kinetic friction between the puck and the ice is 0.11
Explanation:
Given;
initial speed, u = 9.3 m/s
sliding distance, S = 42 m
From equation of motion we determine the acceleration;
v² = u² + 2as
0 = (9.3)² + (2x42)a
- 84a = 86.49
a = -86.49/84
|a| = 1.0296
[tex]F_k = \mu_k N[/tex] = ma
where;
Fk is the frictional force
μk is the coefficient of kinetic friction
N is the normal reaction = mg
μkmg = ma
μkg = a
μk = a/g
where;
g is the gravitational constant = 9.8 m/s²
μk = a/g
μk = 1.0296/9.8
μk = 0.11
Therefore, the coefficient of kinetic friction between the puck and the ice is 0.11
A client with a head injury is being monitored for increased intracranial pressure (ICP). The client's blood pressure is 90/60 mm Hg and the ICP is 18 mm Hg; therefore their cerebral perfusion pressure (CPP) is
Answer:
[tex]CPP=52mm \ Hg[/tex]
Explanation:
Cerebral Perfusion Pressure is obtained by subtracting IntraCranial Pressure(ICP) from the Mean Arterial Pressure(MAP). Adequate cerebral perfusion requires a minimum goal of [tex]70mm \ Hg[/tex]. MAP is obtained using the formula:-
[tex]MAP=\frac{(diastolic \ blood \ pressure\times2)+\ systolic \ blood \ pressure)}{3}\\\\MAP=\frac{2\times60+90}{3}\\\\MAP=70mm \ Hg\\CPP=MAP-ICP\\CPP=70-18\\CPP=52mm \ Hg[/tex]
You are given three iron rods. Two of the rods are magnets but the third one is not. How could you use the three rods to definitively identify the unmagnetized rod?
a. Test the rods a pair at a time in all possible orientations to determine which two rods have the strongest force between them; the leftover rod is unmagnetized.
b. Find one pair of rods that attract when placed end‑to‑end, regardless of orientation; the leftover rod is unmagnetized.
c. Test different pairs of rods in all possible orientations to find a rod that is not attracted to either of the other two rods; that rod is unmagnetized.
d. Test the rods one pair at a time in each possible end‑to‑end orientation until finding a pair that repels; the leftover rod is unmagnetized.
Answer:
d. Test the rods one pair at a time in each possible end‑to‑end orientation until finding a pair that repels; the leftover rod is unmagnetized.
Explanation:
Repulsion is the surest test of magnetisation . If two objects repel each other , they must be magnets . If two objects attract each other , they may not be magnets. In later case , one may be non - magnet. So the last test will help us identify the unmagnetised rod.
In a transpiration experiment, the air bubble has an initial volume of 4.33 mL, and an initial pressure of 101.9 kPa. What will be the pressure reading after the plant transpires 0.26 mL of water from the tubing
Answer:
Explanation:is in the picture below
Assume: The small objects are point particles. The system of seven small 2 kg objects is rotating at an angular speed of 9 rad/s. The objects are connected by light, flexible spokes that can be lengthened or shortened.
A) What is the initial angular momentum of the object?
B)What is the new angular speed if the spokes are shortened from 9 m to 6 m ?
C)What is the new angular momentum of the object?
Answer: a) [tex]L = 10206 kg \cdot \frac{m^{2}}{s}[/tex], b) [tex]\omega_{f} = 20.25 rad/s[/tex], c) [tex]L = 10206 kg \cdot \frac{m^{2}}{s}[/tex]
Explanation:
The angular momentum of a system of particles rotating around an axis is:
[tex]L = \sum_{i=1}^{7} r_{i}^{2} \cdot m_{i} \cdot \omega[/tex]
a) The previous expression can be simplified to find the initial angular momentum:
[tex]L = 7 \cdot r^{2} \cdot m \cdot \omega\\L = 7 \cdot (9 m)^2 \cdot (2kg) \cdot (9 \frac{rad}{s} )\\L = 10206 kg \cdot \frac{m^{2}}{s}[/tex]
b) The new angular speed is calculated from the Principle of Angular Momentum Conservation, since there are no external forces influencing over the system:
[tex]L = 7 \cdot r_{f}^2 \cdot (m) \cdot \omega_{f}[/tex]
[tex]\omega_{f}=\frac{L}{7 \cdot r_{f}^2\cdot m}[/tex]
[tex]\omega_{f} = 20.25 rad/s[/tex]
c) The angular momentum remains constant, since there is no information that indicates the presence of external forces influencing the system.
(A) The initial angular momentum of the object is 10206 kgm²/s
(B) The new angular speed is 20.25 rad/s
(C) The angular momentum does not change
Conservation of angular momentum:All 7 objects have a mass of m = 2kg. The length of the spokes is R = 9m.
(A) The angular momentum of a system is given by:
L = Iω
where I is the moment of inertia of the system
ω is the angular speed = 9 rad/s (given)
L = 7×mR²×ω
L = 7×(2×9²)×9 kgm²/s
L = 10206 kgm²/s
(B) According to the law of conservation of angular momentum, the angular momentum of the system must remain conserved.
So, the new angular momentum is:
L' = 7×(2×6²)×ω'
where ω' is the new angular momentum
10206 = 7×(2×6²)×ω'
ω' = 20.25 rad/s
(C) The new angular momentum of the object is same as the original angular momentum of the object since there is no dissipative force so the angular momentum must be conserved.
Learn more about angular momentum:
https://brainly.com/question/15104254?referrer=searchResults
The temperature within a thin plate with thermal conductivity of 10 W/m/K depends on position as given by the following expression: TT=(100 K)????????−xx2/????????xx 2cos�yy/????????yy�+300 K Where, Lx = 1 m, and Ly = 2 m. At the point (0.4 m, 1 m), find: a. The magnitude of the heat flux b. The direction of the heat flux
Answer:
Heat flux = (598.3î + 204.3j) W/m²
a) Magnitude of the heat flux = 632.22 W/m²
b) Direction of the heat flux = 18.85°
Explanation:
- The correct question is the first image attached to this solution.
- The solution to this question is contained on the second and third images attached to this solution respectively.
Hope this Helps!!!
A proton (being 1836 times heavier than an electron) gains how much energy when moving through a potential increase of one volt?
Answer:
1.6*10⁻¹⁹ J = 1 eV
Explanation:
As the potential is defined as energy per unit charge, the increase in the electrical potential energy of a proton, can be written as follows:[tex]\Delta U_{e} = e*\Delta V[/tex]
where e = 1.6*10⁻¹⁹ C, and ΔV = 1 V = 1 J/C⇒ [tex]\Delta U_{e} = e*\Delta V = 1.6e-19 C* 1.0 V = 1.6e-19 J = 1 eV[/tex]
As the electrical potential energy only depends on the charge and the voltage, the mass has no influence.Explanation:
Below is an attachment containing the solution.
Suppose that you wish to fabricate a uniform wire out of1.15 g of copper. Assume the wire has aresistance R = 0.300 , and all ofthe copper is used.
(a) What will be the length of the wire?
(b) What will be the diameter of the wire?
Answer:
(a) L = 149.2 cm
(b) d = 0.033 cm
Explanation:
Note that the resistivity of copper is
[tex]\rho = 1.72\times 10^{-8}~{\rm \Omega . m} = 1.72\times 10^{-6}~{\rm \Omega.cm}[/tex]
and the mass density of copper is
[tex]d = 8.96~{\rm g/cm^3}[/tex]
We will use the following formula to relate the resistance to other parameters
[tex]R = \frac{\rho L}{A} = \frac{\rho L}{\pi r^2}[/tex]
If all the copper with 1.15 g is used, then
[tex]m = dV\\1.15 = 8.96 \times (L\pi r^2)\\L\pi r^2 = 0.128[/tex]
Back to the resistance:
[tex]0.3 = \frac{1.72\times 10^{-6} L}{\pi r^2}\\L = \pi r^2 (1.74\times 10^5)\\L = \frac{0.128}{L}(1.74\times 10^5)\\L = 149.2~{\rm cm}[/tex]
Then, the diameter is
[tex]149.2\times \pi r^2 = 0.128\\r = 0.0165~{\rm cm}\\d = 2r = 0.033~{\rm cm}[/tex]
When an object slides down an inclined plane, the angle between the displacement and the force of gravity is the same as the angle that the surface makes with the horizontal. Suppose you have a 2-kg cart rolling a distance of 1.5 m down a 30° incline. According to Eq. (7.8), what is the work done on it by the force of gravity? Select One of the Following:
(a) 3J
(b) 25.5 J
(c) 2.6J
(d) 14.7 J
Answer:
(d) 14.7 J.
Explanation:
Using the equation,
W = mghsin∅................. equation 1
Where W = work done on the cart by the force of gravity, g = acceleration due to gravity, h = height, ∅ = angle between the displacement and the force of gravity.
Given: m = 2 kg, g = 9.8 m/s², h = 1.5 m, ∅ = 30°
Substitute into equation 1
W = 2(9.8)(1.5)sin30
W = 2×9.8×1.5×0.5
W = 14.7 J.
The right option is (d) 14.7 J
The work done by gravity on a 2-kg cart rolling down a 1.5 m, 30° incline is 14.7 J, corresponding to option (d).
Explanation:When an object slides down an inclined plane, the work done by gravity can be calculated using the formula W = mgh, where W is the work done, m is the mass of the object, g is the acceleration due to gravity (9.8 m/s2), and h is the vertical height. The vertical height can be determined from the incline's length and the angle of inclination using the sine function (h = l · sin(θ)). For a 2-kg cart rolling a distance of 1.5 m down a 30° incline, the work done by gravity would be W = m · g · l · sin(θ) = 2 kg · 9.8 m/s2 · 1.5 m · sin(30°) = 2 · 9.8 · 1.5 · 0.5 = 14.7 J, which corresponds to option (d).
A centrifuge accelerates uniformly from rest to 15,000 rpm in220s. Through how many revolutions did it turn in this time?
Answer:
27588
Explanation:
Given,
Speed of the centrifuge = 15000 rpm
time, t = 220 s
Revolution = ?
1 min = 60 s
Speed of centrifuge = [tex]\dfrac{15000}{60}[/tex]
= 250 rps
Initial angular speed = 0 rps
[tex]\alpha = \dfrac{250-0}{220}[/tex]
[tex]\alpha = 1.14\ rev/s^2[/tex]
Now,
revolution
[tex]\theta = \omega_0 t - \dfrac{1}{2}\alpha t^2[/tex]
[tex]\theta = 0 + \dfrac{1}{2}\times 1.14\times 220^2[/tex]
[tex]\theta = 27588\ rev[/tex]
Hence, the number of turns is equal to 27588.
Air exits a turbine at 200 kPa and 1508C with a volumetric flow rate of 7000 liters/s. Modeling air as an ideal gas, determine the mass flow rate, in kg/s.
Answer:
mass flow rate = 11.464 kg/sec
Explanation:
given data
P = 200 kPa = 2 × [tex]10^{5}[/tex] Pa
temperature = 150°C = 423 k
volumetric flow rate = 7000 liters/s
solution
first we get here molar flow rate that is express as
molar flow rate = [tex]\frac{Pv}{RT}[/tex] .................1
put here value
molar flow rate = [tex]\frac{2 \times 10^5 \times 7}{8.314\times 423}[/tex]
molar flow rate = 398.06 mol/sec
and
now we get mass flow rate
mass flow rate = molar flow rate × average mol weight ..............2
mass flow rate = 398.06 × 28.8
mass flow rate = 11464.3 g/sec
mass flow rate = 11.464 kg/sec
Final answer:
The mass flow rate of air exiting the turbine is calculated using the ideal gas equation and the given conditions of pressure, temperature, and volumetric flow rate. By substituting the values into the equation, the mass flow rate is found to be 11.6 kg/s.
Explanation:
The problem involves finding the mass flow rate of air using the ideal gas model, given the exiting conditions from a turbine. The known variables are the pressure (200 kPa), temperature (150°C which is 423.15 K after conversion from Celsius to Kelvin), and volumetric flow rate (7000 liters/s or 7 m³/s). To find the mass flow rate, we can use the ideal gas equation PV = mRT, where P is the absolute pressure, V is the volume flow rate per unit time, m is the mass flow rate, R is the specific gas constant for air, and T is the absolute temperature.
The specific gas constant for air (R) is 287 J/kg·K, and it can be solved for m as:
m = PV / (RT)
Substituting the given values:
m = (200,000 Pa)(7 m³/s) / (287 J/kg·K)(423.15 K)
m = 11.599 kg/s (rounded to three significant figures)
Therefore, the mass flow rate of the air exiting the turbine is 11.6 kg/s.
The intensity of a linearly polarized electromagnetic wave is directly proportional to the square of the electric field (e.g., I = k*E2). If the Receiver’s meter reading was directly proportional to the incident microwave’s intensity, the meter would read the relationship M = Mocos2 θ. Plot this relationship. Based on your graphs, discuss the relationship between the meter reading of the Receiver and the polarization and magnitude of the incident microwave.
Answer:
Please find attached file for complete answer solution and explanation of same question.
Explanation:
Consider a rigid steel beam of length L = 13 m and mass mb = 388 kg resting on two supports, one at each end. A worker of mass mw = 74 kg sits on the beam at a distance x from support A. Refer to the figure.
When the worker sits at a distance x = 7.5 m from support A, calculate the force, in newtons, that support B must exert on the beam in order for it to remain at rest. Use g with three significant figures.
Answer:
2321 N
Explanation:
Let g = 9.807 m/s2
Assume this is a uniform beam and the center of mass it at the geometric center, which is half way between the 2 ends, or h = 13/2 = 6.5 m from the left end (support A).
For the system to remain at rest, then the total moments around a point (let pick support A) must be 0. Moments created by each force is the product of the force magnitude and the moment arm, aka distance from the force to support A
[tex]\sum M_A = 0[/tex]
[tex]M_w + M_b + M_B = 0[/tex]
[tex]F_wx + F_bh + F_BL = 0[/tex]
[tex]m_wgx + m_bgh = -F_BL[/tex]
If we take upward direction be the positive direction, that means all the gravity acting downward are negative
[tex]74*(-9.807)*7.5 + 388(-9.807)*6.5 = -F_B13[/tex]
[tex]-13F_B = -30176.139[/tex]
[tex]F_B = -30176.139/-13 = 2321 N[/tex]
So the force at support B has a magnitude of 2321 N acting upward
The force that support B must apply to keep the beam balanced when the worker sits at a distance of 7.5m from support A is approximately 1597.92 N.
Explanation:This problem involves understanding of statics, specifically the principle of moments or torques. Assuming the system is in equilibrium (i.e., the beam does not rotate or translate), the sum of the forces and the sum of the torques must both be zero.
We start by calculating the total weight of the beam, which is simply its mass multiplied by the acceleration due to gravity, g. This gives mb * g = 388 kg * 9.81 m/s^2 = 3806.68 N, this force acts in the middle of the beam, that is at a distance of L/2 = 13m/2 = 6.5m from each support.
Similarly, the weight of the worker is given by mw * g = 74 kg * 9.81 m/s^2 = 725.94 N, this force acts at a distance of x = 7.5m from the left support (A) and L - x = 13m - 7.5m = 5.5m from the right support (B).
Now we can calculate the net force (Fn) and the net torque (Tn). We choose the left support (A) as the pivot point. The total force acting on the beam is the sum of the weights of the beam and the worker, and this must be supported by the two supports. Since sum of the forces must be zero: Fn = F_A + F_B = mass_beam * g + mass_worker * g.
The net torque is calculated from the forces acting at a distance from the pivot point. So we get, Tn = beam_weight * distance_beam - worker_weight * distance_worker + F_B * L = 0. From this, we can solve for F_B (force at support B), we find: F_B = (beam_weight * distance_beam - worker_weight * distance_worker) / L.
Plugging into these formulas, we get the force that support B must apply to keep the system in balance: F_B = (3806.68 N * 6.5m - 725.94 N * 7.5m) / 13m = 1597.92 N.
Learn more about static equilibrium here:https://brainly.com/question/29316883
#SPJ3
A copper rod of length 27.5 m has its temperature increases by 35.9 degrees celsius. how much does its length increase?(unit=m)
Explanation:
When copper rod is heated , its length increases
The increase in length can be found by the relation
L = L₀ ( 1 + α ΔT )
here L is the increased length and L₀ is the original length
α is the coefficient of linear expansion and ΔT is the increase in temperature .
The increase in length = L - L₀ = L₀ x α ΔT
Substituting all these value
Increase in length = 27.5 x 1.7 x 10⁻⁵ x 35.9
= 1.87 x 10⁻² m
Answer:0.01678325m
Explanation:
Original length(L1)=27.5m
Temperature rise(@)=35.9°C
Linear expansivity(α)=0.000017
Length increase(L)=?
L=α x L1 x @
L=0.000017 x 27.5 x 35.9
L=0.01678325m
A 20-kg child starts at the center of a playground merry-go-round that has a radius of 1.5 mm and rotational inertia of 500kg⋅m2 and walks out to the edge. The merry-go-round has a rotational speed of 0.20 s−1 when she is at the center.
What is its rotational speed when she gets to the edge?
Answer:
w = 0.189 rad/ s
Explanation:
This exercise we work with the conservation of the moment, the system is made up of the merry-go-round and the child, for which we write the moment of two instants
Initial
L₀ = I₀ w₀
Final
[tex]L_{f}[/tex] = I w
L₀ = L_{f}
I₀ w₀ = I_{f} w
.w = I₀/I_{f} w₀
The initial moment of inertia is
I₀ = 500 kg. m2
The final moment of inertia
[tex]I_{f}[/tex] = 500 + m r²
I_{f} = 500 + 20 1.5
I_{f} = 530 kg m²
Initial angular velocity
w₀ = 0.20 rad / s
Let's calculate
w = 500/530 0.20
w = 0.189 rad / s
Teams red and blue are having a tug-of-war. According to Newton's third law, the force with which the red team pulls on the blue team exactly equals the force with which the blue team pulls on the red team.
Answer: The statement is TRUE.
Explanation: The Newton's third law states that a body that experiments an external force responds with an opposite force with same magnitude. Therefore, the statement is true.
An uncharged metal sphere, A, is on an insulating base. A second sphere, B, of the same size, shape, and material carrying charge Q is brought close to, but not touching, sphere A. Describe what happens to the charges on A and B as they are brought close but not touching. If we now remove sphere B and place it far away, what is the charge on sphere A
Answer:
0
Explanation:
If we bring the charged sphere B close to, but not touching it , to the uncharged sphere A, as charges can move freely on the conductor, a charge -Q will be built on the outer surface of the sphere A, facing to sphere B.As the sphere A must remain neutral, a charge Q will be built on the surface, on the side farther to the sphere B, as the following condition must be met:Q +(-Q) =0.
If we now remove sphere B, and place it far away, there will be a charge redistribution within sphere A, making to disappear the separation between Q and -Q.The total charge on sphere A must be 0, as there is no charge transfer from sphere B to sphere A.Final answer:
When identical conducting spheres A and B with charges of –5 nC and –3 nC respectively are brought into contact, the total initial charge of –8 nC is shared equally. Upon separation, each sphere holds a final charge of –4 nC.
Explanation:
When two conducting spheres, A and B, with different charges are brought into contact, the total charge is shared equally between them. Given sphere A has a charge of –5 nC and sphere B has a charge of –3 nC, the total initial charge is –8 nC. This charge will be evenly distributed between both spheres when they touch.
Therefore, after spheres A and B are brought into contact and then separated, the final charge on each sphere will be half of the total charge. This final charge will be calculated as follows:
Total charge before contact: –5 nC + –3 nC = –8 nCCharge on each sphere after contact and separation: –8 nC / 2 = –4 nCThus, after separation, both sphere A and B will have a charge of –4 nC each.
The atoms that constitute your body are mostly empty space, and structures such as the chair you're sitting on are composed of atoms that are also mostly empty space. So why don't you fall through the chair
Explanation:
As we all know that the atom mainly composed of two parts, Nucleus at the center and the electrons dancing around it. And, yes there is a vast distance between nucleus and the electrons and it's about ten billionth of a meter. So the question is if there is such an empty space then why not our body just move through the chair and fall? So the answer is, it's all due to the forces. Just like the cracking of lightning through the void, specks of electrons and nuclei are constantly interacting through the force called electromagnetic forces. During each interaction there is an exchange of energy particles called photons. So the each photon swapped is equals to the push or pull or the forces exerted across the emptiness. So these forces enable us to sit on chair or to do other things.