Answer:
a) The magnitude of the magnetic field = 7.1 mT
b) The direction of the magnetic field is the +z direction.
Explanation:
The force, F on a current carrying wire of current I, and length, L, that passes through a magnetic field B at an angle θ to the flow of current is given by
F = (B)(I)(L) sin θ
F/L = (B)(I) sin θ
For this question,
(F/L) = 0.113 N/m
B = ?
I = 16.0 A
θ = 90°
0.113 = B × 16 × sin 90°
B = 0.113/16 = 0.0071 T = 7.1 mT
b) The direction of the magnetic field will be found using the right hand rule.
The right hand rule uses the first three fingers on the right hand (the thumb, the pointing finger and the middle finger) and it predicts correctly that for current carrying wires, the thumb is in the direction the wire is pushed (direction of the force; -y direction), the pointing finger is in the direction the current is flowing (+x direction), and the middle finger is in the direction of the magnetic field (hence, +z direction).
What is the phase angle of an AC series circuit that is constructed of a 14.5-Ω resistor along with 16.5-Ω inductive reactance and 9.41-Ω capacitive reactance?
Answer: cosθ = 0.7531
Explanation: the phase angle cosθ is given as
cosθ = R/Z
Where R = resistive reactance = 14.5 ohms
Z = impeadance = √R^2 +(Xl - Xc)^2
Where Xl = inductive reactance = 16.5 ohms and Xc= capacitive reactance = 9.41 ohms
By substituting the parameters, we have that
Z = √14.5^2 + (16.5^2 - 9.41^2)
Z = √210.25 + (272.25 - 88.5481)
Z = √210.25 + 183.7019
Z = √393.9519
Z = 19.85 ohms
Z = 19.85 ohms, R = 14.5 ohms
cosθ = R/Z = 14.5/19.85
cosθ = 0.7531
26.06°
Explanation:Given an RLC circuit [a circuit containing a capacitor, inductor and resistor], the phase angle (Φ), which is the difference in phase between the voltage and the current in the circuit, is given by;
Φ = tan⁻¹ [ [tex]\frac{X_{L} - X_{C}}{R}[/tex]] --------------------------(i)
Where;
[tex]X_{L}[/tex] = inductive reactance of the circuit
[tex]X_{C}[/tex] = capacitive reactance of the circuit
R = resistance of the circuit
From the question;
[tex]X_{L}[/tex] = 16.5 Ω
[tex]X_{C}[/tex] = 9.41 Ω
R = 14.5 Ω
Substitute these values into equation (i) as follows;
Φ = tan⁻¹ [ [tex]\frac{16.5 - 9.41}{14.5}[/tex]]
Φ = tan⁻¹ [ [tex]\frac{7.09}{14.5}[/tex]]
Φ = tan⁻¹ [ 0.4890]
Φ = 26.06°
Therefore the phase angle of the AC series circuit is 26.06°
A flat circular loop of radius 0.10 m is rotating in a uniform magnetic field of 0.20 T. Find the magnetic flux through the loop when the plane of the loop and the magnetic field vector are perpendicular.'
Answer:
[tex]\phi=6.28\times10^{-3}\;\;weber[/tex]
Explanation:
Given,
Magnetic field [tex]B=0.2\;\;T\\[/tex]
Radius [tex]r=0.1\;\;m[/tex]
The angle between the area vector and magnetic field is 0 degree, because the direction of area vector is always perpendicular to the plane.
[tex]\phi=BAcos\theta\\\phi=o.2\times\pi (0.1)^2\times cos0^o\\\phi=0.00628\;\;weber\\\phi=6.28\times10^{-3}\;\;weber[/tex]
The magnetic flux through a flat circular loop rotating in a uniform magnetic field is zero when the plane of the loop and the magnetic field vector are perpendicular.
Explanation:To find the magnetic flux through the loop when the plane of the loop and the magnetic field are perpendicular, we will need to use the formula for magnetic flux:
Φm = BA cos θ
where Φm is the magnetic flux through the surface, B is the magnitude of the magnetic field, A is the area of the loop, and θ is the angle between the magnetic field direction and the normal (perpendicular) to the surface. In this case, if the loop and the magnetic field are perpendicular, θ = 90°, and cos 90° = 0. Hence, the magnetic flux will be zero.
However, if the provided problem included a different angle, we would adjust the equation to accommodate that. For example, if the field were parallel to the loop (θ = 0), then cos θ would equal 1 and the magnetic flux would just be the product of B and A (A = πr²)
Learn more about Magnetic Flux here:https://brainly.com/question/36474474
#SPJ11
A steel bucket contains 4 liters of water at 128C. An electric immersion heater rated at 1400 Watts is placed in the * Indicates an advanced level in solving. Problems 61 62 CHAPTER 1 Introduction bucket. Determine how long it will take for water to heat to 708C. Assume that the empty bucket weighs 1.1 kg. The specific heat of steel is 0.46 kJ/(kg 8C). Use an average specific heat of water of 4.18 kJ/(kg 8C). Disregard any heat loss to the surroundings.
Answer:
The time is 0.713 sec.
Explanation:
Given that,
Weight of water = 4 liters
Initial temperature = 128°C
Power = 1400 Watts
Final temperature = 708°C
Weight = 1.1 kg
Specific heat of steel = 0.46 kJ/kg°C
Specific heat of water = 4.18 kJ/kg°C
We need to calculate the heat gained by bucket
Using formula of heat
[tex]Q_{b}=mc\Delta T[/tex]
Put the value into the formula
[tex]Q_{b}=1.1\times0.46\times(70-12)[/tex]
[tex]Q_{b}=29.348\ kJ[/tex]
We need to calculate the heat gained by water
Using formula of heat
[tex]Q_{w}=mc\Delta T[/tex]
Put the value into the formula
[tex]Q_{w}=4\times4.18\times(70-12)[/tex]
[tex]Q_{w}=969.76\ kJ[/tex]
We need to calculate the total heat
Using formula of heat
[tex]Q=Q_{b}+Q_{w}[/tex]
Put the value into the formula
[tex]Q=29.348+969.76[/tex]
[tex]Q=999.108\ kJ[/tex]
We need to calculate the time
Using formula of time
[tex]t=\dfrac{Q}{P}[/tex]
Put the value into the formula
[tex]t=\dfrac{999.108}{1400}[/tex]
[tex]t=0.713\ sec[/tex]
Hence, The time is 0.713 sec.
Why do you think it would be more practical to use an electromagnet to move scrap metal than to use a permanent magnet?
Using an electromagnet to lift scrap metal is advantageous because it can be turned off to release the metal, and its strength can be adjusted to handle different loads.
Using an electromagnet to move scrap metal is more practical than using a permanent magnet for several reasons. Firstly, an electromagnet can be turned on and off, useful when you want to release the metal after lifting it. This is not possible with a permanent magnet, which would require a physical effort to detach the metal pieces. Secondly, the strength of an electromagnet can be adjusted by controlling the electric current. This allows for strong magnetic effects that can be finely tuned for the weight and type of scrap being lifted. Lastly, industrial electromagnets can be designed to lift thousands of pounds of metallic waste, which might not be feasible with the size and strength of a permanent magnet.
However, there are limits to how strong electromagnets can be made, mainly due to coil resistance leading to overheating. In cases where extremely strong magnetic fields are necessary, such as in particle accelerators, superconducting magnets may be employed, although these also have their limits, since superconducting properties can be destroyed by excessively strong magnetic fields.
Describe how an uncharged pith ball suspended from a string can be used to test whether an object is charged. Predict what will happen when an uncharged pith ball is brought near one of the poles of the magnet. Explain.
Answer:
Pithball electroscope is used to determine if any object has static charge.
It consists of one or two small balls of a lightweight non-conductive substance. When this material is moved near an object having static charge, polarization will be induced in the atoms of pithballs which will either attract or repel the object depending on the nature of the charge in it.
It will not move in case it is brought near to a neutral object.
Similarly, the pith ball will move when it will brought into the magnetic field of the magnet as it will also induce polarization within the atoms of the pithballs.
Tarik winds a small paper tube uniformly with 183 turns 183 turns of thin wire to form a solenoid. The tube's diameter is 9.49 mm 9.49 mm and its length is 2.09 cm 2.09 cm . What is the inductance, in microhenrys, of Tarik's solenoid?
143μH
Explanation:The inductance (L) of a coil wire (e.g solenoid) is given by;
L = μ₀N²A / l --------------(i)
Where;
l = the length of the solenoid
A = cross-sectional area of the solenoid
N= number of turns of the solenoid
μ₀ = permeability of free space = 4π x 10⁻⁷ N/A²
From the question;
N = 183 turns
l = 2.09cm = 0.0209m
diameter, d = 9.49mm = 0.00949m
But;
A = π d² / 4 [Take π = 3.142 and substitute d = 0.00949m]
A = 3.142 x 0.00949² / 4
A = 7.1 x 10⁻⁵m²
Substitute these values into equation (i) as follows;
L = 4π x 10⁻⁷ x 183² x 7.1 x 10⁻⁵ / 0.0209 [Take π = 3.142]
L = 4(3.142) x 10⁻⁷ x 183² x 7.1 x 10⁻⁵ / 0.0209
L = 143 x 10⁻⁶ H
L = 143 μH
Therefore the inductance in microhenrys of the Tarik's solenoid is 143
The inductance, in microhenrys, of Tarik's solenoid should be considered as the 143μH.
Calculation of the inductance:Since
The inductance (L) of a coil wire (e.g solenoid) should be provided by
L = μ₀N²A / l --------------(i)
here,
l = the length of the solenoid
A = cross-sectional area of the solenoid
N= number of turns of the solenoid
μ₀ = permeability of free space = 4π x 10⁻⁷ N/A²
So,
N = 183 turns
l = 2.09cm = 0.0209m
diameter, d = 9.49mm = 0.00949m
So,
A = π d² / 4
= 3.142 x 0.00949² / 4
= 7.1 x 10⁻⁵m²
Now
L = 4π x 10⁻⁷ x 183² x 7.1 x 10⁻⁵ / 0.0209 [Take π = 3.142]
L = 4(3.142) x 10⁻⁷ x 183² x 7.1 x 10⁻⁵ / 0.0209
L = 143 x 10⁻⁶ H
L = 143 μH
Learn more about length here: https://brainly.com/question/15312768
Two coils of wire are placed close together. Initially, a current of 1.80 A exists in one of the coils, but there is no current in the other. The current is then switched off in a time of 4.02 x 10-2 s. During this time, the average emf induced in the other coil is 4.38 V. What is the mutual inductance of the two-coil system?
Answer: the mutual inductance is - 0.0978H
Explanation:
Detailed explanation and calculation is shown in the image below
Answer:
M = 0.1H
Explanation:
Please see attachment below.
During a very quick stop, a car decelerates at 6.2 m/s2. Assume the forward motion of the car corresponds to a positive direction for the rotation of the tires (and that they do not slip on the pavement). Randomized Variables at = 6.2 m/s2 r = 0.275 m ω0 = 93 rad/s
a. What is the angular acceleration of its tires in rad/s2, assuming they have a radius of 0.275 m and do not slip on the pavement?
b. How many revolutions do the tires make before coming to rest, given their initial angular velocity is 93 rad/s ?
c. How long does the car take to stop completely in seconds?
d. What distance does the car travel in this time in meters?
e. What was the car’s initial speed in m/s?
Answer:
a) [tex]-22.5 rad/s^2[/tex]
b) 30.6 revolutions
c) 4.13 s
d) 52.9 m
e) 25.6 m/s
Explanation:
a)
The relationship between linear acceleration and angular acceleration for an object in circular motion is given by
[tex]a=\alpha r[/tex]
where
[tex]a[/tex] is the linear acceleration
[tex]\alpha[/tex] is the angular acceleration
r is the radius of the motion of the object
For the tires of the car in this problem, we have:
[tex]a=-6.2 m/s^2[/tex] is the linear acceleration (the car is slowing down, so it is a deceleration, therefore the negative sign)
r = 0.275 m is the radius of the tires
Solving for [tex]\alpha[/tex], we find the angular acceleration:
[tex]\alpha = \frac{a}{r}=\frac{-6.2}{0.275}=-22.5 rad/s^2[/tex]
b)
To solve this part of the problem, we can use the suvat equation for the rotational motion, in particular:
[tex]\omega^2 - \omega_0^2 = 2\alpha \theta[/tex]
where:
[tex]\omega[/tex] is the final angular velocity
[tex]\omega_0[/tex] is the initial angular velocity
[tex]\alpha[/tex] is the angular acceleration
[tex]\theta[/tex] is the angular displacement
Here we have:
[tex]\omega=0[/tex] (the tires come to a stop)
[tex]\omega_0 = 93 rad/s[/tex]
[tex]\alpha = -22.5 rad/s^2[/tex]
Solving for [tex]\theta[/tex], we find the angular displacement:
[tex]\theta=\frac{\omega^2-\omega_0^2}{2\alpha}=\frac{0^2-(93)^2}{2(-22.5)}=192.2 rad[/tex]
And since 1 revolution = [tex]2\pi rad[/tex],
[tex]\theta=\frac{192.2}{2\pi}=30.6 rev[/tex]
c)
To solve this part, we can use another suvat equation:
[tex]\omega=\omega_0 + \alpha t[/tex]
where in this case, we have:
[tex]\omega=0[/tex] is the final angular velocity, since the tires come to a stop
[tex]\omega_0 = 93 rad/s[/tex] is the initial angular velocity
[tex]\alpha=-22.5 rad/s^2[/tex] is the angular acceleration
t is the time
Solving for t, we can find the time required for the tires (and the car) to sopt:
[tex]t=\frac{\omega-\omega_0}{\alpha}=\frac{0-93}{-22.5}=4.13 s[/tex]
d)
The car travels with a uniformly accelerated motion, so we can find the distance it covers by using the suvat equations for linear motion:
[tex]s=vt-\frac{1}{2}at^2[/tex]
where:
v = 0 is the final velocity of the car (zero since it comes to a stop)
t = 4.13 s is the time taken for the car to stop
[tex]a=-6.2 m/s^2[/tex] is the deceleration for the car
s is the distance covered during this motion
Therefore, substituting all values and calculating s, we find the distance covered:
[tex]s=0-\frac{1}{2}(-6.2)(4.13)^2=52.9 m[/tex]
e)
The relationship between angular velocity and linear velocity for a rotational motion is given by
[tex]v=\omega r[/tex]
where
v is the linear velocity
[tex]\omega[/tex] is the angular speed
r is the radius of the circular motion
In this problem:
[tex]\omega_0 = 93 rad/s[/tex] is the initial angular speed of the tires
r = 0.275 m is the radius of the tires
Therefore, the initial velocity of the car is:
[tex]u=\omega_0 r = (93)(0.275)=25.6 m/s[/tex] is the initial velocity of the car
If the momentum of a 1000 kg car travelling at 10 m/s was transferred completely to a 20.0 kg traffic barrier, what would the final speed of the barrier be
Answer:
500 m/s
Explanation:
Momentum, p is a product of mass and velocity. From law of conservation of momentum, the initial momentum equals final momentum
[tex]m_1v_1=m_2v_2\\1000*10=20v_2\\v_2=10000/20=500 m/s[/tex]
Here m and v represent mass and velocity respectively and subscripts 1 and 2 represent car and barrier respectively
Therefore, the velocity of barrier will be 500 m/s
Two long, parallel wires are separated by a distance of 3.30 cm. The force per unit length that each wire exerts on the other is 5.00×10−5 N/m, and the wires repel each other. The current in one wire is 0.620 A.
a. What is the current in the second wire?
b. Are the two currents in the same direction or in opposite directions?
Answer with Explanation:
We are given that
Distance between two parallel long wires=r=3.3 cm=[tex]\frac{3.3}{100}=0.033m[/tex]
1 m=100 cm
[tex]\frac{F}{l}=5\times 10^{-5} N/m[/tex]
[tex]I_1=0.62 A[/tex]
a.We have to find the current in the second wire.
We know that
[tex]\frac{F}{l}=\frac{2\mu_0I_1I_2}{4\pi r}[/tex]
Using the formula
[tex]5\times 10^{-5}=\frac{2\times 10^{-7}\times 0.62\times I_2}{0.033}[/tex]
Where [tex]\frac{\mu_0}{4\pi}=10^{-7}[/tex]
[tex]I_2=\frac{5\times 10^{-5}\times 0.033}{2\times 10^{-7}\times 0.62}[/tex]
[tex]I_2=13.3 A[/tex]
Hence, the current in the second wire=13.3 A
b.We are given that the wires repel each other.When the current carrying in the wires in opposite direction then, the wires repel to each other.
Hence,the two currents in opposite directions.
Two charged particles are separated by 10 cm. suppose the charge on each particle is doubled. By what factor does the electric force between the particles change?
Answer:
The electric force increases by a factor of 4.
Explanation:
The electric force between two charges [tex]q_1[/tex] and [tex]q_2[/tex] separated a distance d can be calculated using Coulomb's Law:
[tex]F=\frac{kq_1q_2}{d^2}[/tex]
where [tex]k=9\times10^9Nm^2/C^2[/tex] is the Coulomb constant.
If the value of each charge is doubled, then we will have a force between them which is:
[tex]F'=\frac{k(2q_1)(2q_2)}{d^2}=4\frac{kq_1q_2}{d^2}=4F[/tex]
So the new force is 4 times larger than the original force.
Doubling the charge on each particle increases the electric force between them by a factor of 4.
Explanation:The force between two charged particles is given by Coulomb's Law, which states that the force is directly proportional to the product of the charges and inversely proportional to the square of the distance between them. So, if we denote the electric force as F, the charges as q1 and q2, and the distance as r, we can write Coulomb's law as F = k* q1*q2/r^2, where k is a constant.
Now if you double the charges (q1 and q2 become 2q1 and 2q2), and use these values in the formula, we get Fnew = k*(2q1) *(2q2)/r^2 = 4 * k*q1*q2/r^2 = 4F.
So, by doubling the charge on each particle, the electric force between them is multiplied by the factor of 4. So, the force increases fourfold.
Learn more about Coulomb's Law here:https://brainly.com/question/32002600
#SPJ3
Determine the voltage ratings of the high-and-low voltage windings for this connection and the MVA rating of the autotransformer connection.17 pointsb. Calculate the efficiency of the transformer in this connection when it is supplying its rated load at unity power factor. 17 points
Complete Question
The complete question is shown on the first uploaded image
Answer:
a
The High Voltage Rating for Auto - Transformer is 86kV
The Low Voltage Rating for Auto - Transformer is 78kV
The MVA rating is 268.75[tex]MVA[/tex]
b
The efficiency is 99.4%
Explanation:
From the question we are given are given that
The transformer has Mega Volt Amp rating of 25MVA
The frequency is 60-Hz
Voltage rating 8.0kV : 78kV
The short circuit test gives : 453kV,321A,77.5kW
The open circuit test gives : 8.0kV, 39.6A, 86.2kW
This can be represented on a diagram shown on the second uploaded image
From this diagram we can deduce that the The High Voltage Rating for Auto - Transformer is 86kV and the Low Voltage Rating for Auto - Transformer is 78kV
Now to obtain the current flowing through the 8kV coil in the Auto-transformer we have
[tex]\frac{25 \ Mega \ Volt\ Ampere }{8\ Kilo Volt}[/tex]
The volt will cancel each other
[tex]\frac{25*10^6}{8*10^3} = 3125\ A[/tex]
Now to obtain the required MVA rating we would multiply the value of Power obtained during the open circuit test by the value of the current calculated.we are making use of the power obtain during open circuit testing because the transformer at this point is not under any load.
[tex]MVA \ rating = (86*10^3)(3125) =268.75[/tex]
We need to understand that Iron losses is due to open circuit test which has power = 86.2kW
While copper loss is due to short circuit test which has power = 77.5kW
The the current flowing through the secondary coil [tex]I_2[/tex] as shown in the circuit diagram can be obtained as
[tex]I_2 = \frac{25*10^6}{78*10^3} =320.52 A \approx 321[/tex]
Now the efficiency can be obtained as thus
[tex]\frac{(operational \ MVA )*(Power factor \pf))}{(operational\ MVA (power factor pf) + copper loss + Iron loss)}*\frac{100}{1}[/tex]
=99.941%
You sit at the middle of a large turntable at an amusement park as it begins to spin on nearly frictionless bearings, and then spins freely. When you crawl toward the edge of the turntable, does the rate of the rotation increase, decrease, or remain unchanged, and why
Answer:
Explanation:
As there is no external torque is applied so the angular momentum remains constant.
L = I ω = constant
Where, I is the moment of inertia of the system and ω is the angular velocity
As we move towards the edge, the moment of inertia increases, hence the angular velocity decreases.
A 6861 kg car traveling at 48 m/s is at the foot of a hill that rises 142 m in 2.3 km. At the top of the hill, the speed of the car is 10 m/s. The acceleration of gravity is 9.81 m/s 2 . Assuming constant acceleration, find the average power delivered by the car’s engine, neglecting any internal frictional losses.
Answer: P = 25050.8w
Explanation:
total energy at top = K.E + P.E
= (1/2)(6861)(100) + 6861(9.81)(142)
total energy at bottom
= (1/2)(6861)(48)^2
work done = energy at top - energy at bottom
average velocity = (48+10)/2
time = 2300/average velocity
power = work done/time
plus potential) at the base and the top; is the energy input from the engine
the ascent time is the average speed, (top + bottom) / 2; divided by the 2.3 km distance
energy / time equals power
A horizontal power line carries a current of 7250 A from south to north. Earth's magnetic field (65.7 µT) is directed toward the north and is inclined downward at 70.0° to the horizontal. Find the (a) magnitude and (b) direction of the magnetic force on 140 m of the line due to Earth's field.
Answer:
a) [tex]||\vec F_{B}||=62.664\,N[/tex], b) From east to west.
Explanation:
Vectorially, the magnetic force can be calculed by the following formula:
[tex]\vec F_{B} = i\cdot \vec l\, \times \, \vec B[/tex]
The cross product is:
[tex]\vec F_{B} = \left|\begin{array}{ccc}i&j&k\\1015000\,A\cdot m&0\,A\cdot m&0\,A\cdot m\\22.471\times 10^{-6}\,T&-61.738\times 10^{-6}\,T&0\,T\end{array}\right|[/tex]
[tex]\vec F_{B} = - 62.664\,N\cdot k[/tex]
a) The magnitude of the magnetic force is:
[tex]||\vec F_{B}||=62.664\,N[/tex]
b) The direction of the magnetic force is:
From east to west.
Air enters a horizontal, well-insulated nozzle operating at steady state at 12 bar, 500 K, with a velocity of 50 m/s and exits at 7 bar, 440 K. The mass flow rate is 1 kg/s. Determine the net force, in N, exerted by the air on the duct in the direction offlow.Answer:
Answer:
The net force is 300.8 N
Explanation:
∆H = Cp(T1 - T2) = 1/2(V2^2 - V1^2)
Cp is the heat capacity of air at constant pressure = 1005 J/kg
T1 is initial temperature of air = 500 K
T2 is the exit temperature of air = 440 K
V1 is the initial velocity of air = 50 m/s
V2 is the exit velocity of air
1005(500 - 440) = 1/2(V2^2 - 50^2)
60,300×2 = V2^2 - 2,500
V2^2 = 120,600 + 2,500 = 123,100
V2 = sqrt(123,100) = 350.8 m/s
Net force (F) = mass flow rate × change in velocity = 1 kg/s × (350.8 - 50)m/s = 1 kg/s × 300.8 m/s = 300.8 kgm/s^2 = 300.8 N
The net force exerted by the air on the duct in the direction of flow is approximately [tex]\( 0.00293 \) N[/tex].
Given:
- Inlet conditions (state 1):
- [tex]\( P_1 = 12 \) bar = \( 12 \times 10^5 \) Pa[/tex]
- [tex]\( T_1 = 500 \) K[/tex]
- [tex]\( v_1 = 50 \) m/s[/tex]
- Exit conditions (state 2):
- [tex]\( P_2 = 7 \) bar = \( 7 \times 10^5 \) Pa[/tex]
- [tex]\( T_2 = 440 \) K[/tex]
- Mass flow rate, [tex]\( \dot{m} = 1 \) kg/s[/tex]
1. Calculate specific volumes:
[tex]\( v_1 = \frac{RT_1}{P_1} = \frac{287 \times 500}{12 \times 10^5} \approx 0.02379 \) m^3/kg[/tex]
[tex]\( v_2 = \frac{RT_2}{P_2} = \frac{287 \times 440}{7 \times 10^5} \approx 0.02086 \) m^3/kg[/tex]
2. Calculate the change in specific volume:
[tex]\( \Delta v = v_2 - v_1 = 0.02086 - 0.02379 = -0.00293 \) m^3/kg[/tex]
3. Calculate the net force in the direction of flow:
[tex]\( F = \dot{m} \cdot \Delta v = 1 \cdot (-0.00293) = -0.00293 \) N[/tex]
Since the force is negative, it indicates that the force is acting opposite to the direction of flow.
Therefore, the net force exerted by the air on the duct in the direction of flow is approximately [tex]\( 0.00293 \) N[/tex].
There is a spot of paint on the front wheel of the bicycle. Take the position of the spot at time t=0 to be at angle θ=0 radians with respect to an axis parallel to the ground (and perpendicular to the axis of rotation of the tire) and measure positive angles in the direction of the wheel's rotation. What angular displacement θ has the spot of paint undergone between time 0 and 2 seconds? Express your answer in radians using three significant figures.
Answer:
[tex]\int\limits^2_0 {w} \, dt[/tex]
Explanation:
If Angular velocity w (omega ) is given, which is defined as, w = (change in angle)/(change in unit time).
then simply taking integral from 0 to 2 gives us the answer.
Answer:
Change in theta = 0.793rad
Explanation:
Please see attachment below.
after a circuit has been turned off, so it is important to make sure they are discharged before you touch them. Suppose a 120 mF capacitor from a camera flash unit retains a voltage of 150 V when an unwary student removes it from the camera. If the student accidentally touches the two terminals with his hands, and if the resistance of his body between his hands is 1.8 kΩ, for how long will the current across his chest exceed the danger level of 50 mA?
Answer:
The time is [tex]110.16\times10^{-3}\ sec[/tex]
Explanation:
Given that,
Capacitor = 120 μF
Voltage = 150 V
Resistance = 1.8 kΩ
Current = 50 mA
We need to calculate the discharge current
Using formula of discharge current
[tex]i_{0}=\dfrac{V_{0}}{R}[/tex]
Put the value into the formula
[tex]i_{0}=\dfrac{150}{1.8\times10^{3}}[/tex]
[tex]i_{0}=83.3\times10^{-3}\ A[/tex]
We need to calculate the time
Using formula of current
[tex]i=\dfrac{V_{0}}{R}e^{\frac{-t}{RC}}[/tex]
Put the value into the formula
[tex]50=\dfrac{150}{1.8\times10^{3}}e^{\frac{-t}{RC}}[/tex]
[tex]\dfrac{50}{83.3}=e^{\frac{-t}{RC}}[/tex]
[tex]\dfrac{-t}{RC}=ln(0.600)[/tex]
[tex]t=0.51\times1.8\times10^{3}\times120\times10^{-6}[/tex]
[tex]t=110.16\times10^{-3}\ sec[/tex]
Hence, The time is [tex]110.16\times10^{-3}\ sec[/tex]
The current across the student's chest will exceed the danger level for approximately 216 seconds.
Explanation:The current that flows through the student's chest when he accidentally touches the terminals of the 120 mF capacitor can be calculated using Ohm's law: I = V/R, where I is the current, V is the voltage, and R is the resistance. In this case, the voltage is 150 V and the resistance of the student's body is 1.8 kΩ. Plugging in these values, we can find the current.
I = (150 V)/(1.8 kΩ) = 0.0833 A
To find how long the current will exceed the danger level of 50 mA, we need to calculate the time it takes for the charge on the capacitor to dissipate through the student's body. Since the current is constant, we can use the formula Q = I*t, where Q is the charge and t is the time. Rearranging the formula, we can solve for t.
t = Q/I = (120 mF * 150 V) / (0.0833 A) = 216 s
Therefore, the current will exceed the danger level of 50 mA for approximately 216 seconds.
Learn more about Circuit Discharge here:https://brainly.com/question/35876531
#SPJ12
Alex is asked to move two boxes of books in contact with each other and resting on a rough floor. He decides to move them at the same time by pushing on box A with a horizontal pushing force FP = 8.9 N. Here, A has a mass mA = 10.2 kg and B has a mass mB = 7.0 kg. The contact force between the two boxes is FC. The coefficient of kinetic friction between the boxes and the floor is 0.04. (Assume FP acts in the +x direction.)
Answer:
Explanation:
The force of friction acting on the system
= .04 x 9.8 ( 10.2 + 7 )
= 6.74 N
Net force = 8.9 - 6.74
= 2.16 N
Acceleration in the system
= 2.16 / ( 10.2 + 7 )
= .12558 m / s ²
Contact force between boxes = FP
Considering force on box A
Net force = 8.9 - FP
Applying Newton's law on box A
8.9 - FP = 10.2 x .12558
= 1.28
FP = 8.9 - 1.28
= 7.62 N
A 84.0 kg ice hockey player hits a 0.150 kg puck, giving the puck a velocity of 36.0 m/s. If both are initially at rest and if the ice is frictionless, how far (in m) does the player recoil in the time it takes the puck to reach the goal 24.0 m away? (Enter the magnitude.)
Answer: 3333333222135790075
Explanation:Set term u equal to initial velocity for simplicity
Set V equal to final velocity for simplicity
2
To begin this problem, one must look at the system to have multiple stages. These being before and after hitting the puck. In these first few steps, we look at BEFORE the human hits the puck
3
This collision is elastic because the puck and the human do not join together after interaction
4
Because the initial velocity of both the puck and the human are both 0, the terms on the left of the equal sign become 0
5
Solving for the final velocity of the human gives this formula. This number should be negative as the negative indicates the direction he is going (left)
The final velocity of the puck is already given in the problem
6
Because the ice is frictionless, the final velocity before hitting the puck is equal to the initial velocity after hitting the puck
Now we begin to look at the system AFTER the puck has been hit
7
Using the formula for final position allows us to solve for time it takes the puck to travel the distance given
8
9
Solve for time
10
We can now use the formula for the final position of the human to solve for the final answer
11
12nuewnfunw
Plugging in formulas from steps 5 and 9 gives the final answer
Again, this number should be negative as the negative sign denotes the direction the human is going. Because the problem does not ask for snijndij hinu9nub hvtj c v7 yf jhmb tfgnb nb fyhgbv
The distance traveled by the player ( recoil ) in the time the puck reaches the goal is 0.043m.
What is law of conservation of linear momentum?According to the law of conservation of momentum, the sum of the momentum of the object before and after the collision must be equal.
m₁ u₁ + m₂ u₂ = m₁ v₁ + m₂ v₂
where m₁ and m₂ is the mass of the objects, u₁ and u₂ are initial speed while v₁ & v₂ is final speed.
Given the initial velocity of the player is u₁ = 0 and the puck is u₂ = 0
The mass of the player m₁ = 84 Kg
The mass of the puck, m₂ = 0.150 Kg
The final velocity of the puck, v₂ = 36 m/s
From the law of conservation of momentum, find the velocity of the player:
m₁ u₁ + m₂ u₂ =m₁ v₁ + m₂v₂
84 × 0 + m ×0 = 84 × v + 0.150 × 36
v = - 0.064 m/s
A negative sign shows the player and puck moving in the opposite direction.
Now, we calculte the time taken for the puck to trach the goal:
Time = Distance/ Velocity
t = 24/36 = 0.667 sec
Next, we calculate the distance traveled by the player( recoil ) in the time of 0.667 seconds.
Distance = Velocity× time
S = 0.064 ×0.667
S = 0.043m
Therefore, the distance covered by the player in the time the puck reaches the goal is 0.043m.
Learn more about the law of conservation of linear momentum, here:
brainly.com/question/17140635
#SPJ5
Three identical resistors, when connected in series, transform electrical energy into thermal energy at a rate of 12 W (4.0 W per resistor). Part A Determine the power consumed by the resistors when connected in parallel to the same potential difference. Express your answer with the appropriate units.
Answer:
108 Watts
Explanation:
The total circuit resistance when the resistors are connected in series is
R + R + R = 3R
When he resistors are connected in parallel, the resistance reduces from 3R in the series circuit to become;
[tex]\frac{1}{R} + \frac{1}{R} + \frac{1}{R}[/tex]
= [tex]\frac{R}{3}[/tex] Ω
[tex]Power = \frac{V^{2}}{R}[/tex]
The voltage supply was given to be constant for both the series and parallel circuits. This implies that V² is constant and power is inversely proportional to resistance.
Therefore;
Power for the parallel connected circuit = [tex]\frac{3R}{\frac{R}{3} } * 12 W[/tex]
= 9 × 12 W = 108 Watts
Answer:
Explanation:
Potential difference, V and let each resistance, R
Resistors are in series, total resistance, Rₓ = R1 + R2 + R3
= R + R + R
= 3R
Power, P = V²/Rₓ
12 = V²/3R
V²/R = 36
Resistors are in parallel, total resistance, 1/Rₓ = 1/R1 + 1/R2 + 1/R3
Rₓ = R/3
P = V²/Rₓ
P = V²/(R/3)
P = 3(V²/R)
= 3(36)
= 108 W.
The maximum allowed power dissipation for a 23.9 Ω 23.9 Ω resistor is stated to be 10.0 W . 10.0 W. Calculate the largest current that this resistor can take safely without burning out.
Answer:
0.65 A.
Explanation:
Given:
Pmax = 10 W
R = 23.9 Ω
Formula for calculating power,
P = I × V
= I^2 × R
I^2 = 10/23.9
I = 0.65 A.
A certain monatomic gas inside a cylinder is at a temperature of 22°C. It takes 353 J of work done on the gas to compress it and increase the temperature to 145°C. If there are originally 8.2 moles of gas inside the cylinder, calculate the quantity of heat flowing into or out of the gas. (Indicate the direction with the sign of your answer. Let "into the gas" be positive, and "out of the gas" be negative.)
The calculated heat Q is [tex]\( 1.22 \times 10^4 \mathrm{~J} \),[/tex] and the positive sign indicates that heat is being added to the system.
Let's break down the given answer step by step:
1. Given Values:
Temperature of gas, [tex]\( T = 22^{\circ} \mathrm{C} = 295 \mathrm{~K} \)[/tex]
Work done on the gas to compress it, [tex]\( W = -353 \mathrm{~J} \)[/tex](negative because work is done on the gas)
Final temperature, [tex]\( T_f = 145^{\circ} \mathrm{C} = 418 \mathrm{~K} \)[/tex]
Number of moles,[tex]\( n = 8.2 \) moles[/tex].
2. First Law of Thermodynamics:
The first law of thermodynamics is given by [tex]\( Q = \Delta U + W \),[/tex] where Q is the heat added to the system, [tex]\( \Delta U \)[/tex] is the change in internal energy, and W is the work done on the system.
For a monoatomic gas,[tex]\( C_v = \frac{3}{2} R \),[/tex]
where R is the universal gas constant [tex](\( R = 8.314 \mathrm{~J} \mathrm{~K}^{-1} \mathrm{~mol}^{-1} \)). So, \( Q = n C_v \Delta T + W \).[/tex]
3. Calculation:
Substituting the given values into the equation:
[tex]\[ \begin{aligned} Q & = \left(8.2 \times \frac{3}{2} \times 8.314 \times (418 - 295)\right) + (-353) \\ & = 12225 \mathrm{~J} = 1.22 \times 10^4 \mathrm{~J} \end{aligned} \][/tex]
4. Interpretation:
Since Q is positive, it means heat is flowing inside the cylinder. A positive value of Q indicates that the system is gaining heat, and in this case, it's due to both the compression work done on the gas and the increase in internal energy.
In summary, the calculated heat Q is [tex]\( 1.22 \times 10^4 \mathrm{~J} \),[/tex] and the positive sign indicates that heat is being added to the system.
The current theory of the structure of the Earth, called plate tectonics, tells us that the continents are in constant motion. Assume that the North American continent can be represented by a slab of rock 4700 km on a side and 25 km deep and that the rock has an average mass density of 2880 kg/m3 . The continent is moving at the rate of about 3.2 cm/year. What is the mass of the continent
The mass of the North American continent is calculated by multiplying the volume of the continent by the density of the rock it is made of. The volume is determined based on the given dimensions, converted to meters. Multiplying the resulting volume by the rock's density provides the estimated mass of 1.59712e21 kilograms.
Explanation:In order to find the mass of a continent, we need to multiply the volume of the continent by the density of the rock that it's made of. First, we need to convert the dimensions of the North American continent into meters from kilometers since the density is in kg/m³. That's 4700km x 1000m/km =4.7e6m for length & width, and 25km x 1000m/km = 2.5e4m for depth. Thus, the volume of the continent becomes 4.7e6m x 4.7e6m x 2.5e4m = 5.54e17m³.
Now, we multiply by the rock's density, which is 2880 kg/m³. So, mass = volume * density = 5.54e17 m³ x 2880 kg/m³ = 1.59712e21 kg. So, the theoretical mass of the North American continent is approximately 1.59712e21 kilograms considering its simplified shape as a slab of rock.
Learn more about Mass of a Continent here:https://brainly.com/question/38293151
#SPJ12
A conducting loop is placed in a magnetic field. What must be true for there to be a current induced in the loop? (1 point) There must be a source of charge The magnetic field must be changing Potential energy must change into kinetic energy The loop must be surrounded by insulating material
Answer:
EMF will induce in the conducting loop when
The magnetic field must be changing
Explanation:
As per Farady's law of EMI we know that the magnetic flux linked with the closed conducting loop must be changed with time
so we have
[tex]EMF = \frac{d\phi}{dt}[/tex]
so we know that
[tex]\phi = BAcos\omega t[/tex]
now if magnetic field is changing with time then we have
[tex]EMF = Acos\theta \frac{dB}{dt}[/tex]
so EMF will induce when magnetic field will change with time
Suppose that at a price of $2.60, the quantity of output demanded is 17, and at a price of $6.30, the quantity of output demanded is 8. What is the elasticity of demand? (Ignore the negative sign.)
Answer: elastic (e = 2.43)
Explanation:
The price elasticity formulae is given below as
Elasticy of price = change in quantity demanded / change in price.
P1 =$2.60, P2 = $6.30, q1 =17 and q2 = 8
e = q2 - q1/ P2 - P1
e = 8 - 17/ 6.30 - 2.60
e = - 9 /3.7
e = - 2.43
We take the modulus of e to have a positive value. Hence e = 2.43
Since e is greater than 1, then the elasticity of demand is elastic
Final answer:
The elasticity of demand between the given prices is calculated using the midpoint formula. It results in a value of -0.865 (ignoring the minus sign), indicating that the demand is elastic.
Explanation:
To calculate the elasticity of demand, we can use the midpoint formula, which is defined as the percentage change in quantity demanded divided by the percentage change in price. The formula for computing elasticity is:
Price Elasticity of Demand (Ed) = ([(Q2 - Q1) / ((Q2 + Q1)/2)] / [(P2 - P1) / ((P2 + P1)/2)]) * 100
Using the information provided: At a price of $2.60, quantity demanded is 17, and at a price of $6.30, quantity demanded is 8. We can fill in the values:
(Q2 - Q1) is (8 - 17) = -9
(Q2 + Q1)/2 is (8 + 17)/2 = 12.5
(P2 - P1) is ($6.30 - $2.60) = $3.70
(P2 + P1)/2 is ($6.30 + $2.60)/2 = $4.45
Now putting all these into the formula:
Ed = [(-9 / 12.5) / (3.70 / 4.45)] * 100
The percentage change in quantity is -72%, and the percentage change in price is 83.15%. Therefore:
Ed = (-0.72 / 0.8315) * 100
Ed = -0.865 (ignoring the minus sign)
This value is greater than 1, which indicates that the demand is elastic between these two prices; meaning, the quantity demanded is quite responsive to price changes.
Remember, we ignore the negative sign and use the absolute value when discussing elasticity, even though it is understood that price and quantity demanded move in opposite directions.
In general it is best to conceptualize vectors as arrows in space, and then to make calculations with them using their components. (You must first specify a coordinate system in order to find the components of each arrow.) This problem gives you some practice with the components. Let vectors A⃗ =(1,0,−3), B⃗ =(−2,5,1), and C⃗ =(3,1,1). Calculate and express your answers as ordered triplets of values separated by commas
(1) A - B
(2) B - C
(3) - A + B - C
(4) 3A - 2C
(5) - 2A + 3B - C
(6) 2A - 3 (B - C)
Answer:
(1) (3,-5,-4)
(2) (-5, 4, 0)
(3) (-6, 4, 3)
(4) (-3, -2, -11)
(5) (-11, 14, 8)
(6) (17, -12, -6)
Explanation:
A⃗ =(1,0,−3)
B⃗ =(−2,5,1)
C⃗ =(3,1,1)
Vector additions and subtraction are done on a component by component basis, that is, only data from component î can be added to or subtracted from another Vector's component î. And so on for components j and k.
1) (A - B) = (1,0,−3) - (−2,5,1) = (1-(-2), 0-5, -3-1) = (3,-5,-4)
2) (B - C) = (−2,5,1) - (3,1,1) = (-2-3, 5-1, 1-1) = (-5, 4, 0)
3) -A + B - C = -(1,0,−3) + (−2,5,1) - (3,1,1) = (-1-2-3, 0+5-1, 3+1-1) = (-6, 4, 3)
4) 3A - 2C = 3(1,0,−3) - 2(3,1,1) = (3,0,-9) - (6,2,2) = (3-6, 0-2, -9-2) = (-3, -2, -11)
5) -2A + 3B - C = -2(1,0,−3) + 3(−2,5,1) - (3,1,1) = (-2,0,6) + (-6,15,3) - (3,1,1) = (-2-6-3, 0+15-1, 6+3-1) = (-11, 14, 8)
6) 2A - 3 (B - C) = 2(1,0,−3) - 3[(−2,5,1) - (3,1,1)] = (2,0,-6) - 3(-5,4,0) = (2+15, 0-12, -6-0) = (17, -12, -6)
A proton moves through an electric potential created by a number of source charges. Its speed is 2.5 x 105 m/s at a point where the potential is 1500 V. What will be the proton’s speed a short time later when it reaches a point where the potential is −500 V? The mass of a proton is 27 m 1.67 10 kg.
Answer:
Proton’s speed, a short time later when it reaches a point of lower potential is 1.4 x 10⁵ m/s
Explanation:
Given;
initial speed of proton, u = 2.5 x 10⁵ m/s
initial potential, V = 1500 V
mass of proton = 1.67 x 10⁻²⁷ kg
Work done, W = eV= ΔK.E = ¹/₂mu²
eV = ¹/₂mu² (J)
where;
e is the charge of the proton in coulombs
V is the electric potential in volts
m is the mass of the proton in kg
u is the speed of the proton in m/s
[tex]m =\frac{2eV_1}{u_1{^2}} = \frac{2eV_2}{u_2{^2}} = \frac{V_1}{u_1{^2}}} =\frac{V_2}{u_2{^2}}[/tex]
[tex]\frac{V_1}{u_1{^2}}} =\frac{V_2}{u_2{^2}} = \frac{1500}{(2.5*10^5)^2} = \frac{500}{u_2{^2}} \\\\u_2{^2} =\frac{500*(2.5*10^5)^2}{1500} = 0.333*6.25*10^{10}\\\\u_2 = \sqrt{0.333*6.25*10^{10}} =1.4 *10^5 \ m/s[/tex]
Therefore, proton’s speed a short time later when it reaches a point of lower potential is 1.4 x 10⁵ m/s
Oxygen (O 2 ) is confined to a cubic container, 15 cm on a side, at a temperature of 300 K. Compare the average kinetic energy of a molecule of the gas to the change in its gravitational potential energy if it falls from the top of the container to the bottom.
Answer: Average kinetic energy is greater than gravitational potential energy.
Explanation: The average kinetic energy formulae for a molecule of a gas relative to temperature (in Kelvin) is given below as
E = 3/2 (KT).
Where E = average kinetic energy =?
K = boltzman constant = 1.381×10^-23 m²kg/s²k
T = temperature = 300 k
By substituting the parameters in the formulae, we have that
E = 3/2 ×( 1.381×10^-23 × 300)
E = 1.5 × 4.143×10^-21
E = 6.2145×10^-21 J
To get the gravitational potential energy, we use the fact that
Gravitational potential energy = gravitational energy at the top - gravitational energy at bottom.
At the top, the height of cube is h= 15cm = 0.15m, g = acceleration dude to gravity = 9.8m/s², m = mass of molecule of oxygen = 1.661×10^-27 kg
Gravitational potential energy = mgh = 1.661×10^-27× 9.8 × 0.15 = 2.442×10^-27 J
At the bottom, height is zero, hence gravitational potential energy is also zero.
Hence the final gravitational potential energy = potential energy at top - potential energy at bottom =
2.442×10^-27 - 0 = 2.442×10^-27 J.
Gravitational potential energy = 2.442×10^-27 J
Average kinetic energy = 6.2145×10^-21 J
As we can see that the average kinetic energy is bigger than the gravitational potential energy.
Compare the average kinetic energy of oxygen molecules at 300 K to the change in their gravitational potential energy if they fall from the top to the bottom of a container.
Oxygen (O2) molecules at 300 K have an average kinetic energy of 3kT, where k is Boltzmann's constant. If an oxygen molecule falls from the top of a container to the bottom, its change in gravitational potential energy is mgΔh, where m is the mass of the molecule, g is the acceleration due to gravity, and Δh is the height change.
When tension is applied to a metal wire of length L , it stretches by Δ L . If the same tension is applied to a metal wire of the same material with the same cross-sectional area but of length 2 L , by how much will it stretch?
Answer:
The metal wire will stretch by [tex]2 \delta L[/tex]
Explanation:
[tex]T = \frac{kA \delta L}{L}[/tex]......................................(1)
Where T = Tension applied
ΔL = Extension
L = length
k = constant
T₁ = T₂ = T
A₁ = A₂ =A
L₁ = L
L₂ = 2L
(ΔL)₁ = ΔL
(ΔL)₂ = ?
From equation (1)
[tex]TL/kA = \delta L[/tex].....................(2)
[tex]TL/kA = (\delta L) ........................(3)\\ 2TL/kA = (\delta L)_{2} ........................(4)[/tex]
Divide (4) by (3)
[tex]\frac{(\delta L)_{2} }{\delta L} =\frac{\frac{2TL}{kA} }{\frac{TL}{kA} } \\\frac{(\delta L)_{2} }{\delta L} = 2\\ (\delta L)_{2} = 2\delta L[/tex]
If the starting length is twice, the extension is doubled as well.
Given that;
Length of metal wire = L
Stretch = ΔL
So,
It will stretched to a length of 2L.
Although when tension is continuous, the length of the extension is proportional to the size of the initials.
As a result, if the starting length is doubled, the extension will be twice as well.
Learn more:
https://brainly.com/question/17499135?referrer=searchResults